I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Was looking through the reference designs you have in github .
I figured the difference between nRF52840_qiaa_var1 (what is qiaa ?) and nRF52840_qiaa_var2 is the use of...
Hello everyone,
I am facing an issue with UART communication from my nRF52832 to my GPS module.
I precise that communication in the other way works very well (I get...
We have a need to invert the TTL logic for the serial interface. All our "Unique" SWI serial interfaces use an inverted logic e.g. idle state 0 instead of idle state 1.
...
Is there any lnk which uses nrf52 mesh without models.
Means a simple function to send data(like "Hello world") to any node or group in Mesh.
and other node receive data...
Hello, I was wondering, Firstly and more important question, Is there a way in a BLE Mesh standard to physically locate/position the nodes? In order to obtain the distance...
Hello,
After (accidentally) entering bootloader mode on my nRF51 DK (PCA10028), the device doesnt show up either in the device manager or using nRFgo Studio (both not normally...
I bought Nordic nRF52840-DK at an electronics store in Taiwan. J-link cannot be detected when connecting to a computer. I bought two pieces nRF52840-DK. One of them can be...
I've been having lots of issues putting the example projects on the NRF9160 dev kit. It builds without errors, connects to J-Link, but sometimes fails on the download step...
I'm unable to program a nrf52840 dev kit (BMD340 dev kit) using the attached hex file combination of Bootloader and softdevice. Both bootloader and softdevice can be programmed...
Why do I get the folowing error with mbedtls when doing "west update"?
Possibly related issues: * devzone.nordicsemi.com/.../west-update-blocks-and-fails-on-mbedtls (Didn...
Hello All,
I loaded the last FW version (mfwnrf9160100) in my nRF9160 SDK using nRF Connect Programmer and looks fine.
However, the Reset button or AT commands are not...
How would I take a NRF51 Dongle that has the stock firmware from nRF Connect and communicate/send commands to it over something like PuTTY? I've tried sending AT Commands...
Hi
configure as:
ROM start: 0x26000
RAM start: 0x20002218
when I download application software , it pops up following error.
I'm using keil uVison version 5...
Hello! I am doing some development with pc-ble-driver-py and ran in to some unexpected behaviours when reading characteristics. I have been modifying the nus_collector.py...
Hi
In the last few months I posted a question about RTOS and softdevice and I need to read the answer again but I am struggling to find how to do that
Look forward to...
