Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Has anyone used a graphics library like emWin or TouchGfx on nRF52?
www.segger.com/emwin.html
http://touchgfx.com/en/
I do not see any posts on either forums or here...
Hi!,
I'm trying to compile GitHub examples, for example this github.com/.../nrf51-ble-tutorial-service
I cloned it into nRF5_SDK_12.1.0_0d23e2a/examples/peripheral....
Hello,
I have custom board with nRF52832, and I want to have possibility to DFU over UART.
I tested example bootloader (nRF5_SDK_11.0.0\examples\dfu\bootloader\pca10040...
I am using nrf51 SDK v.12.1.
And I found NRF_LOG_INFO("BLINKY START\n");
where can I find this log?
Is this different from SEEGER_WriteString or something?
Hi
We are using "gcc compiler" to compiler our programs. To download our programs we use "nRFgo Studio" app.
From the above image, when we load SDK into the device...
Hello,
Consider this scenario:
The client successfully writes to a characteristic by the application code can't use the data sent so it would be usefull to signal the...
Hello,everyone. Now i have the board nrf52832 and i want it to enter the low-power mode but keep the the advertising. Now the measured current is 160uA, I think there should...
Dear All,
I apologize in advance if it seems that the question has been already posed but it is still unclear to me.
I have a pin (SIG_OK) and I want to read its logic value...
On the nRF51 DK there is a MM8130-2600 connector. I suppose it is used for connecting coax cable when tuning the antenna(?)
The connector is quite expensive, though. Is...
Per the name "UUID" and the very limited background knowledge that I have, it appears that a particular device can have its UUID assigned by its manaufacture, who bought the...
Hello.
I am developing a BLE application on NRF52832 using Nordic SDK11 and S132 softdevice. I use Linux PC as a BLE host device, and can pair & bond the NRF bluetooth...
Hi there! I'm using the nRF Toolbox's UART to test the receiving of my data stream. I'm trying to send a data array collected (from spi) in my main loop and send it via UART...
I am studying the iot-sdk of nordic.
Now, as I have shown in previous questions, I can not detect the device under the linux system according to the toturial in iot.
Now...
Hello, I have device with nrf51822-qfab and I need to run ble_app_template (use softdevice s110). What version of SoftDevice I must to use with SDK v6.1?
About problem:
...
Hi,
I've been trying to add the option for BLE HID to the Espruino JS interpreter on nRF52 - it's something that ideally would be switchable at runtime.
After having...
Dear All
In my application we could not use the ADC inside the nRF51822 because 10bit are under our requirements. But now with the new nRF52xxx with a built-in 12bit ADC...
