Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
Is there a way to change a build configuration after it was created?
I want to change the kconfig fragments it is calling, but I was no able too. I have to delete and create...
I am trying to test TLS communication between TCP server and client so, how I should generate the certificates and how to provision them in TCP server?
Can I use OpenSSL...
Hi, I am using nrf52832 development kit. MCU is waking up with two buttons and I put MCU to system off mode after successful data exchange or timeout. Init settings are like...
Hi,
I am configuring a button and an ISR to handle the events, but the interrupt is not called only when there is a transition.
Is there any other configuration needed...
During the End Of Line test of one of our device, based on nRF52832, we write the serial number of the device in some non volatile registers, specifically CUSTOMER[8] and...
Hello,
We are using the nRF52810-QCAA(QFN32) in a Beacon application. We have seen serious degradation in Radio performance while using the DC/DC vs. the LDO. More than...
Hi Forum,
i've ran into a problem with configure the nrf24l01. I've disabled all ShockBurst functionality (EN_AA = 0). When putting TX Payload into the Fifo the TX_EMPTY...
Hi~
We are going to use the MAC address and UUID as what we have.
I am trying to save the MAC address and UUID through UART, so I don't know what to do.
Currently the...
Hello,
I am trying to make a code running the Ble stack adn the FreeRtos one, i started from the project ble_app_hrs_freertos_pca10040_s132, i've just removed some things...
Hi.
Newbie stuck at installing IDE.
Trying to follow the automatic installation developer.nordicsemi.com/.../gs_assistant.html
Installed nRF Connect for Desktop v3.8...
Hi,
we have nrf52933 custom hardware.
we are flashing application through j-link.
but after every flashing , I need to hard reset the board in order to run the function...
Dear Nordic，
We developed a product based on the nRF52833 chip, with an external antenna, 3dBi gain. Set transmission parameters 100mS interval and 4dBm transmission power...
I have nrf52840 dongle will like to treat it as central. (like gateway) And sensor node is unknow ble, and adress type is Resolvable Private Address. If know the characteristics...
Using the « nrf_modem_at_cmd_async » function triggered an HARD_FAULT error if it is the first function used in the code before another function of the AT interface of the...
Hello everyone I would like to produce my own custom board based on the NRF52840, but the quartz used in the Dk is sell by package of 3000 pcs so I decided to change and use...
