Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hi，
sdk：ncs v1.6.1
board:9160dk_nrf9160
I use RTT to output log data, but I found that it can only output about 1k characters each time. Where can I modify it?
this...
Hi Team,
These are the SDA and SCL lines of nRF52832 connected to a sensor. the clock frequency defined in the code is 400 KHz, but its coming as 200 KHz on oscilloscope...
Hello, I have designed a custom hardware using nRF52833. I tried to program the nRF52833 using nRF52832DK, I am having following connections- nRF DK nRF custom board VTG-VDD...
Hello,
I have applied for the SUPL license and it got denied. I met the criteria which is mentioned by the Nordic.
I did log in the last 4 week and I am the member of...
Hi,
I'm trying to register the SIM card that came with the nRF9160-DK I just received and during SIM registration, it's stuck at the "still working" step indefinitely...
I have custom board with nrf52833 Soc. I was trying to implement WS2812 LED driver in zephyr which connected to ( P1.09). according to WS2812 Sample Application I copy the...
Hi all
Thanks in advance for any hints you could give on this. I would like to measure two pwm signals (frequency and duty cycle) on two input pins of the nrf52832.
board...
In the nRF5 SDK there are two uart drivers, UART and UARTE. The UARTE driver makes use of the DMA whilts the UART driver uses interupts. This is what I understood when I used...
I am considering using this part from MAXIM (MAX31343).
https://datasheets.maximintegrated.com/en/ds/MAX31343.pdf
it is an RTC plus a 5ppm oscillator output that I can...
Hi all,
Now I'm analyzing the bug that is the fault of my application's timing control.
On analyzing, I found the difference that garbage collection callback was delayed...
Hi,
I am using nRF 5340DK borad, trying to flash Direct test mode sample "nordic,nrf5340-dk-nrf5340-cpunet". My aim is the enable direct test mode on the nrF board in order...
I'm using 3 nRF52840 DK borads (provisioner,light_switch_client, DFU). I set DFU (DFU example used) as target board and connected it to PC as serial interface. I have provisioned...
Hai,
I'm facing some difficulties in programming FOTA over UART on the NRF9160 board.
Currently, by using the following command I'm trying to push the bin file via UART...
Hello Team,
I have a small issue but troubling me since a long time now. Accidently my debug terminal and project explorer came out from their original positioning. Now...
