I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hi,
Looked through PS v1.3 didn't see any reference, so probably the answer to my question is no.
But can you please confirm that for me - does nRF52833 support boundary...
Hello,
I am doing tests on nRF9160 DK and I observe that if I send more than 1024 bytes on a TCP or UDP socket, the bandwidth drops.
Here are some numbers :
for...
Hi there
I mount the 19pin connector on nrf5340dk board and connect to segger j-trace pro . The debugger function work well.
Later i modify the nrf9160 etm trace project...
Has anyone had success getting triggers on motion to work with the LIS2DH? I only have INT1 wired so I modified the drivers to work on INT1 as the spec document says it should...
I'm writing software for nRF52832 using nRF5 SDK v17.0.2
I'm using a timer to create a buzz/tone using timer 3. This works as expected.
I'm also using the SAADC to measure...
I'm learning how to use OTA DFU (via BLE) now. I have Python 2 and 3, pip installed in my Win10 laptop. When I install the nrfutil with PowerShell, I had some errors (see...
I've been using the nrf connect toolchain for a bit, and after some initial trouble it was working ok, but now its randomly giving this error whenever I try to build anything...
Hi,
I am trying to convert a number from little endian to big endian. There is a built in function "NTON" that I can use instead of writing my own code, but I can not find...
I'm using two nRF52805 to get sensor values and send 2 sensor real-time values to my phone via BLE. Each nRF52805 BLE works well (Individually tested by nRF Connect App. It...
The encoders I am using generating about 500 pulses per second, and I need to read 3 of them at the same time. I assume a good approach for that is to use the hardware timer...
Hi, working with NCS v1.4.2, I see building products for an <app> landing into subfolder <app>/build/, in several flavours
app_moved_test_update.hex app_signed.hex app_test_update...
Hello,
I'm trying to flash an example code from the SDK onto the Arduino Nano 33 BLE board.
I tried to use the external debugging on an arduino nano 33 ble card but the...
Hi,
I'm using NRF52840 and having a lot of issues with hard fault.
From time to time, I get an application crash with the following log:
HARD FAULT at 0x00000000 R0...
This question may be better suited for the Zephyr forum, but I figured I would ask it here as well in case somebody can easily see what I may be missing.
I am trying to...
