Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi,
I am trying to enable event length extension on uart example provided on the sdk. I look for information on how to done it and i found links like that:
https://devzone...
Hello，
I am using ncs1.7.1, qspi + mx25r64 external flash ota it works well, but I don't know how to change qspi to spi.
I need your help thanks
I change the parament...
Hi Nordic,
I am working on a raspberry pi based gateway which has Thread Border Router and edge node functionality. I have setup the OTBR on the gateway and I have manage...
Hi,
how can I change the standard LED_0 output from P0.17 to P0.03? I am using SES, toolchain 1.8.0 and the nRF52DK board and I would like to flash the sample code to a...
Hello! I have WF200 wi-fi chip connected to the nrf52840 through SPI. I configured bare-metal example code of WF200 chip to work with nrf-sdk and this example (basic CGI server...
No connection after disconnect with Android App Nordic Uart Service until mac-address of smartphone changes
Multilink multirole software developed in SES studio.
Other...
Hi I have a product that uses an Nrf52810 in a Raytec slave module. I am able to successfully send and receive packets of data using your UART app in the nrf Toolbox
I would...
Hi,
1. I need to change the total free space of this file system: Current size:24576 bytes
3. I made the following adjustment, but it didn't work.
4. How do I modify...
nRF Connect for Desktop cannot find any devices from the SELECT DEVICE tab in LTE Link monitor or Bluetooth Low Energy app.
The device can be found on Device Manager and...
Hi, all.
I'm using nRF52833 and trying to communicate ESP8266 using UART.
I already successfully communicate with Dust Sensor with baudrate 9600, so I tried to communicate...
Hi,
I'm trying to find an example of using the I2S audio interface with the Zephyr RTOS on the nRF52840dk_nRF52840 development board or on an nRF52840 device in general...
Hello ! I'm a beginner here, and I have a problem that I struggle to solve. A few years ago, a firmware was done by a company, for the one I work for. It was done with IAR...
Hi,
I am toggling a GPIO using the below code and trying to find out the relation of the frequency and the code statements. I know that GPIO peripheral is running at 16MHz...
Hi,
after fixing a missing ground in my setup (see devzone.nordicsemi.com/.../interaction-jlink-and-power-profiler-ppkii) I have not been able to get less than 50uA of idle...
