void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I am doing power optimizations on a custom hardware that has nrf9160 and nrf52833 on it. These are connected via GPIO pins and I use two pins to send interrupts to each other...
Hello. I am downloading a custom board (nrf52810) using the nrf52832-dk board as shown below.
I compressed and managed the project file after taking over for company business...
Dear Team,
We are developing a product based on ble mesh. We are planning to select NRF52840 as master device and nrf52832 as slave device. Slave devices should be more...
In the ble_app_beacon example in nRF SDK 17.02, there are two defines namely APP_BEACON_INFO_LENGTH (0x17) and APP_ADV_DATA_LENGTH (0x15). The former defines length of the...
I am trying to port some code from the nrf52840dk (PCA10056) to the dongle (PCA10059) and everything seems to work fine until an interrupt is triggered. All serial output...
Hey! I have a project with custom board with nRF52833 and I would need help with just getting data from sensor via i2c and sending it via bluetooth to mobile device. For some...
Hey!
I would like to use the nrfjprog executable from the nrf command line tools for flashing the nrf9160 modem firmware. I read some older tickets about this issue and...
I have a requirement to start the MCU with extended non connectable advertisement for few minutes and then activate normal connectable advertisement for another few minutes...
Hello,
We have an app_timer that runs periodically for the application, and we are also using BLE peripheral code. Once the application timer expires, the event handler...
Hi,
The Dongle was given to me by a colleague of mine who has the exact same laptop as I do. The Dongle was and is working fine with his laptop. The problem is with my office...
Hi ,
i am using nrf52832 soc with customize board trying to optimize the power the following events occur:
1)The first time when i code uploaded it initialize all the...
Hi,
Is there a way to set somewhere in the softdevice or a library to automatically disconnect after an idle connection? Idle means, nog characteristics being read or written...
Dear Nordic,
I have some questions when study the usb audio of nRF52840;
What function when running the nrf_drv_usbd_errata_104 function?
Do I have run it? Can I remove...
Hi,
I am struggling to find a basic sample for UART communication in NCS. As an experienced Nrf5 SDK programmer, I find it very hard to convert my firmware to nRF Connect...
