Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hello!
I am currently working on a project with my nRF52832 that is using BLE communication with a android phone. I have tried some of Nordics' examples that use BLE, but...
Hi all,
I have a question concerning the nRF52833.
I'd like to know if there is a safety limit on the amount of reflected power that is reflected by the antenna inside...
Dear Nordic,
I changed the value in the Bootloader to not erase the 4k just before the bootlader.
NRF_DFU_APP_DATA_AREA_SIZE 4096
In the app I changed the rom size...
Hi,
I dont know if this is the right forum to ask, but is there any common solution for certificate renewal?
For example If I use azure iot hub, I will provision the...
Hi everyone
I apologize in advance for any possible mistakes.
I am new to programming nRF52 series microcontrollers.Having started exploring various possibilities, I ran...
Hi,
We've been developing our application using pc-ble-driver which communicates with a PCA10040 devkit with SD API v5.1 connectivity firmware. In this dev environment,...
I'm trying to connect to a few sensors on the Nordic Thingy:52, and it fails with the following message: characteristic is not defined. The connection to the Thingy is established...
Hi,
i use nrf51822 and sdk 11.0 . I am using the ble_app_hrs_c example .This product consists of two devices，One master and one slave.
The master chip is nrf51822...
I am using the nRF52840 (with SDKv17.0.0 + s140_7.0.1) and made a custom FW based on the ble_app_hrs example. My custom HW has a 64MB S25FS512S flash memory chip.
I found...
Hi,
I am currently trying to run the DFU over UART example using my nrf52840 dk. I am using sdk v15.2.0. I followed the following instructions found in the Nordic Infocenter...
I have done a DFU code in our Customized board using NRF52832. My program was running successfully in nrf52 DK but in our customized board it's not working
While uploading...
Hi, I have a BME280 sensor running normally with the nRF9160 on v1.2.0 firmware. When I updated the firmware to 1.3.1, I had to update the code to run I updated the files...
Hi, I have a simple voltage divider circuit and I am measuring analog input from in between the resistors. I am using a custom NRF52832 being powered by a DK. I get quite...
