Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I am using a nrf52840 dongle with SEGGER. I am trying to find the security mode and level of the bluetooth initially and after getting paired to another device too. My moto...
Hello. If using an nRF52840 as a coordinator, there seems to be a hard limit of 200 connected devices:
#define ZB_CONFIG_OVERALL_NETWORK_SIZE 200U
At least that's how...
Hello:
I have a problem here:
Connecting ... - Connecting via USB to probe/ programmer device 0 - Probe/ Programmer firmware: J-Link OB-nRF5340-NordicSemi compiled Apr...
Hello everyone,
I am planning to use the nRF9160 as the main microcontroller for my project. Alongside this, I need a Bluetooth module to transmit data to a mobile phone...
I'm using an nRF52840 as BLE peripheral with a custom service similar to NUS to send large data. The data is send in 4k chunks via BLE notifications to an Android phone. With...
In the nrf5340 Product Specification, the GPIO registers OUT, DIR, LATCH, DETECTMODE, DETECTMODE_SEC, and PIN_CNF[n] are all labeled as "Retained Registers". The definition...
I have had luck setting up signatures using MCUBOOT and sysbuild. However, I have not been able to encrypt the images. sysbuild.conf: SB_CONFIG_BOOTLOADER_MCUBOOT=y SB_CONFIG_BOOT_SIGNATURE_KEY_FILE...
I have a product that uses the nRF5 SDK that I do not plan to migrate to the nRF Connect SDK. My product uses ocrypto 3.0.8, which shipped with the latest version of the nRF5...
Hello,
I have an NRF9160DK board and a custom board running the SLM application that are exhibiting similar behaviour. Both boards work fine with the supplied iBasis SIM...
Here's a weird error, that started happening seemingly overnight: paths being parsed wrong on windows due to path separating backslashes being interpreted as escape sequences...
Hi,
I have done some searching and cannot find a direct answer to this. I have a gpio pin defined in a custom device in my board dts. I want to set this pin to high drive...
Is it posiible to use bt_disable on the nrf5340 board? for some reason it doesn't work, returns and error on this line:
if ( ! bt_dev . drv -> close ) {
return - ENOTSUP...
Hi all,
I need to modify the app.overlay dts overlay in mcuboot to be able to see the printout, among other small details. I was able to change them in the "C:/ncs/v2.5...
I'm switching from STM32 to nRF52840 and it's for a battery-operated device that only wakes up every few hours and only stays awake for about 10 seconds. With the STM32 (and...
One of our products uses the NRF51822 for Bluetooth communication.
This product is now undergoing CE certification. Is there a CE DoC (Declaration of Conformity) for the...
