Hi，
When I use NCS V2.5.0 （board：nRF 52840），I want to set the Non-Connectable and Scannable Extended Advertising.My code as follows.I use the APP nRF Connect for moblie...
Hi Nordic team.
I'm finding a way to update the factory data over-the-air. Specifically, I want to update the Matter Certification information (PAI, DAC, ...) over-the-air...
Hi，
In Core Specification v5.4, there is support for Non-Connectable and Non-Scannable Extended Advertising (ADV_EXT_IND) without AUX packets. However, when using Nordic...
When both ethernet and WiFi are supported on one MCU (with both sharing the same L2 implementation, only one network device being active at a time), does it matter if both...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
Since I need zephyr version 4.0 or newer, I tried updating my project to the nRF Connect SDK v3.0.0 as well as the toolchain. I know that they are not fully released yet....
Hello,
I am a beginner when working with nRF. I am trying to run the l4_e3 solution code, but it doesn't seem to work. I can connect via BLE, but nothing is being shown...
Hi,
I have a question concerning time zone support in nRF SDK >= 1.9.1 for nrf9160.
I'm trying to implement an LwM2M client that should be able to convert a UTC datetime...
NCS 2.7.0/2.8.0
mcuboot + MCUMGR in the application for BLE DFU
NRF52840
We have been developing our next version of our product, transitioning from NRF SDK 5 to NCS...
Hi，
When I used NCS V2.5.0,after two devices successfully establish a BLE connection but then disconnect due to a timeout, subsequent reconnection attempts fail with error...
I have a BLE system where multiple sensors operate as peripherals and send data to a BLE central. These sensors enter sleep mode after transmitting data and later wake up...
Hi all,
I applied QSPI driver on NCS 2.4.0 with QSPI LCD panel and I encountered the problem.
The red area is the data I sent, but the blue area is not what I sent....
Hello,
I designed a PCB using nRF52840 for controlling the board.
I have physical access to the following pins : SWDIO, SWDCLK , VSS , VDD , nRESET.
What is the boot...
Hi,
I'm trying to test DTM over USB CDC with an nRF5340DK unfortunately, Direct Test Mode desktop App is not detecting the DK.
Build command (copied from VSCode output...
Hey folks,
i have to use the nrf9160 board to create a PoC for a project of our company. The main topic of the PoC is not important here because i cant even connect to an...
Hi,
We are on NCS v2.9.1
We have an existing project on based on the nrf52832, which we use as a hci_spi controller. There, CONFIG_BT_LL_SW_SPLIT is set. We are now porting...
Hi, I have encountered issues flashing a NRF52833 board which is on a custom PCB. I have picked the project up from another developer so it is somewhat developed already....
hi,
I am reviewing development in the environment below.
* HW : nRF52832
* SW : SDK -> example -> ble_app_uart_c
In the nRF52-DK board, we reviewed the example...
hi support team,
i want to confirm the FEM control when using nrf21540ek for mesh demo "light" with 52840dk.
i set :
CONFIG_BT_CTLR_TX_PWR_ANTENNA =20
CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB...
Hello Team,
I am trying to set configurations for FOTA. I refer smv_server sample code and the following document https://docs.nordicsemi.com/bundle/ncslatest/page/nrf/app_dev...
We are using the NRF9151 and unable to establish a connection to an LTE-M network in Ireland (testing in Cork currently). We are using a Kore MVNO SIM which supports Three...
Hi,
I am trying to upload data from two sensors, the BME280 and APDS9960, to the nRF Cloud. I have been able to extract data from the sensors with I2C, but it seems I am...
