I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
I ran into an issue using RTT on recent SDKs: In SDK15.3 and up RTT stopped working in Segger Embedded Studio. Here's what I found in case others are having the same issue...
Hi,
We are having single Main supply VDD to nRF9160 SoC, which is powering both CoreM33 and Modem.
So this indicates Modem will be always ON when Core M33 is ON.
Is...
Hi everyone,
Following some tutorials as well some examples provided by SDK16 I was able to create a custom service with a characteristic that has read,write and notify...
Hi All,
I am using NRF5 SDK 17, I have been playing with several examples and noticed that when it comes set up, a peripheral or a priority or clock source there will...
I started modifying the NRF Android Blinky example project to suits my needs (to control a servo motor). I observed there is a BIG delay between writings to a specific characteristic...
Hi guys,
Is it possible to read the data in Minicom if my device is not connected directly with my laptop. Instead of that, I connected my external voltage source to supply...
Hi, I am using the nrf mem_manager library for allocationg multiple dynamic memories in my code. I have done the following
All the devices are getting the allocation for...
I am using a custom board based on nRF52840. Application is working perfectly, and then a new feature was requested. I need to count the number of minutes the application...
Hello guys,
We are developing a device that will based on nRF9160 SiP. We use nRFConnect SDK v1.3.0 . The goal would be to connect to AWS IoT through MQTT and exchange messages...
Hi,
In one module of an application I would like to statically declare a large buffer in SRAM: static uint8_t largeBuffer[65536];
The application fails to link with the...
Hi,
I have been implementing the GPS on my thingy:91 with the firmware v1.2.0
I'm able to do a cold start and get a FIX is if in do not move the board for around 100...
Hello，I am using SDk14.1.Sometimes w hen I send data to nrf52832 via serial port，the code prompted me "APP_UART_COMMUNICATION_ERROR".And t he value of the ERRORSRC register...
Hi, I am trying to perform an OTA DFU of SD + BL on nRF52840, upgrading the SoftDevice from 6.1.1 to 7.0.1.
I have been able to do a DFU of application only, and it works...
