It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hello, I'm prototyping using nrf52832 with BMD-300. On my new board I design, I need 3.6V tension (and not just 3.3), so I thought setting everything to 3.6V, including the...
Hi,
I'm currently doing a current consumption test for bluetooth mesh using PCA10056. I want to label the plot like the ones in Online Power Profiler, but it turns out I...
Hi. Does anyone know where I can download the CDC ACM diver for windows 7?
I am running the example on the nRF52 dev kit, but I get an error as windows can't find the driver...
Hi all,
I'm currently implementing a Bluetooth Mesh system for testing various network characteristics.
I am running some tests were a Nordic Thingy:52 is sending a lot...
Hi, I have read the "nRF91 AT Command Reference Guide v0.7" and I would like to propose a new AT command to be added and also an additional feature to an existing AT command...
Dear nordic:
I am confused of NRF51824 MTU issue, NRF51824 can use S130 softdevice, S130 is qualified bluetooth 4.2 core spec, then why S130 features don't included MTU...
While trying to find out a realistic maximum power consumption target I was searching for the power consumption of the LPCOMP comparator. I've seen a few claims about 0.5...
Hello,
I want to send data from central device to peripheral device. I am currently using nRF52DK.
While sending data from peripheral to central device, data is sent successfully...
hello all,
I buy the Fanstel EV-BC832 V2 and start to paying with it.
I used the IAR ide and Embedded studio (SEGGER) ide for my tests.
First i check the blinky and...
I development nRF52832, I want change mac address.
So I modified nRF5_SDK15.0.0/examples/ble_peripheral/ble_app_uart.
I added code to the examples.
////////////////...
Hi everyone,
I want to program the nrf51822 module with the discovery board stm32f429i-disc1 through ST-LINK programmer in Keil IDE but this error appears: "ST-LINK connection...
Dear DevZone Team,
I am an absolute beginner in the field of mesh networking and hope you could help me getting started. Please bear with me.
I have a bunch of sensors...
Does anyone uses Sloeber to program nRF52? I have an issue, when I add a header nrf_temp.h to the project and using following functions:
The problem appears when I add...
Dear Nordic team,
We are developing a BLE application for IOS and Android. On Android, we utilized your Nordic Scanner Lib to scan Bluetooth devices and it is fine and...
