Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I tried to use fstorage to store some data in flash.
From now, I was able to read and write data before advertising starts, but when I try to write data to flash after...
Hi,
I am currently trying to perform DFU update over BLE, I am working on SDK v11.0, and Softdevice S130 v2.0.0. My traget is an nRF51822-QFACA1.
When I enter in bootloader...
Hello everybody,
I'm designing an app to track the position of the smartphone using six beacons and, in order to do that, I made some measures both indoors and outdoors...
Is there any example combining the Serial and Over the Air DFU for the SDK13?
Or the posiblity to combining the two features into a single bootloader?
What steps should...
Iprogram the bootloader.hex to 0x78000 with jlink.Then in my application program,I set the NRF_UICR->NRFFW[0] register as belew:
static void write_uicr_customer_register...
When power on,run app first at 0x1f000,then reset and run to boot loader at 0x78000,how to set UICR registers to make this come true?I try to set the NRF_UICR->NRFFW[0] in...
Hello,
I want to build a system which will use 2 nrf8001 to communicate. 1 nrf8001 will act as a client by continuously transmitting its UUID and another one will act as...
I am working on RTLS project. I want to perform DFU in beacons but not getting proper information .I went through ( devzone.nordicsemi.com/.../) but i think it i for SDK 13...
I have a hex string like this 58FF1CE5.This is corresponding to One date time 16/09/1955 .(ie in MM/dd/yyyy).How can i do this in ObjectiveC, I am getting this date in didDiscovercharacterstivc...
After some search I found that accepted values for tx power are -40, -30, -20, -16, -12, -8, -4, 0, and 4 dBm.
So my questions are
once I set the tx power using ...
I will code 1 to 2, however, was not successful
code1 :
u8 IICwriteBytes(u8 dev, u8 reg, u8 length, u8* data){
u8 count = 0;
IIC_Start();
IIC_Send_Byte(dev);...
Hello Nordic Team,
I would like to know if it is possible to do a DFU of my SDK10 based application ( s130_nrf51_1.0.0_softdevice + SDK10 Bootloader ) on an nRF51822 (32...
Hello to everyone in this community,
I am new with NordicSemi chips and I have the Development kit 52832. I opened the example folder from the SDK 13, SPI slave and i saw...
Hii all,
I am working on a project where I need to store data to persistent storage and retrieve back when the board is restart. but now we are migrated to simultaneous...
