Hello!
We are planning to purchase an electronic component nrf52840 and produce a finished product on it.
question
1. Will it work immediately on the ZIGBEE 3.0...
Good morning, I have a question about NRF Util. I need to make some changes in souce code of nrfutil for my own needs, but the most recent version, which is provided on Github...
Hi. I interested now for direction finding in nrf52 series. I have nrf52811, nrf52833 and other controllers. But i don't find any information how develop board for recievers...
Zephyr Eddystone example is connectable after power on of nrf52833 board. But after disconnect it becomes non connectable. How to fix it? And how to change advertisement interval...
We are looking for an experienced software developer, for existing board with using nRF Connect SDK. We are using nRF52840-dk.
Please, contact me if you are interested.
Hello Nordic,
We developed our product using MCU NRF52840-QFAA-F-R. Our client is based in the EU. We plan to launch our product in 1-2 months.
I have a few questions...
Hello,
I am working on a prototype Bluetooth Low Energy module using the MDBT50Q-512K (by Raytac).
To measure the frequency of this prototype with test equipment, I am...
has been helping me connect to a device and I am finally able to do that, but as soon as I do, Zephyr crashes.
This is with a lightly modified central_uart project [00:00...
While creating a new board in step 2 of the exercise, there are a couple of problems with the sub-steps 1-5:
First, sub-step 1 says to name the board "DevAcademy nRF52833...
Hello,
I've been using the libuarte module in my project, and I done a power consumption reading. With libuarte switched on I'm consuming 0.78ma, and with it switched off...
We have been seeing a bootloop issue on some of our nRF52840 boards running NCS v2.6.1 using CR2032 coin cell batteries. The batteries are all around 3V.
This is an intermittent...
ON NCS SDK 2.7.0 version, how to calibrate SAADC?
I checked below code, I see that "Perform calibration before the reading is taken if requested.", it will trigger calibration...
I am developing a product for a customer using NRF9151(ncs2.7.0, modem fw: mfw_nrf91x1_2.0.2). While verifying it on the DK board, I discovered an issue. When the system starts...
Hi!
I'm writing new firmware for the nrf54 family, and I want to have a system timer with 1s resolution (clock). This clock will be occasionally synchronized with epoch...
I am currently working through the Nordic Academy - SDK Intermediate Course - Lesson 2 Exercise 3, found here:
academy.nordicsemi.com/.../
I am not seeing any of the...
Hi,
Going through the nRF Connect SDK Intermediate course on Lesson 2 exercise 2 step 9 there is a command ncs_install_path/PathToToolChain/opt/zephyr-sdk/aarch64-zephyr...
Hi,
I've recently brought up the Matter Test Harness on a Raspberry Pi following the instructions in the CERT tool repository ( https://github.com/project-chip/certification...
I know the default answer is no, stopping nrf24 and get a RF52 or nRF53 series but my question is about an existing product. We are not all FORD, we can not just do a mass...
Dear Nordic Support Team,
I'm currently working with your Flutter library, mcumgr_flutter version 0.4.1, to implement Device Firmware Update (DFU) functionality. However...
At first you only did that for nrf apps, which was already annoying, but I could live with it: https://github.com/nrfconnect/sdk-zephyr/commit/3239cf77c0ed7c58aefb1f368c8ad17303b16ef5...
