Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
The NRF5340 net core crashes in sdc_hci_cmd_le_set_adv_enable() if I have CONFIG_CLOCK_CONTROL_NRF_CALIBRATION_MAX_SKIP set to 0.
To reproduce the issue, do the following...
Hi ,
I am using nrf52833dvk and nrf52832 boards, am working on application that my nrf52833 board do the firmware updation of other board i.e. nrf52832 . first time i did...
We plan to incorporate the nRF9160 into many thousands of our devices, however this leads to a question of procuring SIM cards. We purchased a Thingy91 to test the connectivity...
The iBASIS sim card came with Thingy:91 does not work. Got the replacement card today. However, I cannot finish the nRF cloud reg process. The new error message said
Tenant...
Hello, I am trying to load a sample project in VS Code using the nRF Connect SDK extension.
I try to load a sample project, click on "Create Application", and nothing...
I am trying to use the NRFx Softdevice controller, with Rust and the nRF5340. I have successfully initialized the library, but when I try to start to start advertising the...
Hi! I'm unable to connect my development kit to a network with the provided iBasis SIM card. I'm located in Bristol UK. According to this [ https://ibasis.com/solutions/iot...
To provide feedback to the user through the LED state, I would like the behavior to be something like this:
If the nRF52840 Zigbee device is unpaired and ready for a ZC...
Hi support,
I'm currently having issue trying to program a nrf52833 device using Jlink mini on mac. I have no problem programming the device using a pro Jlink on windows...
Hi,
I'm trying to use examples. The ICM42605 example does not work.
I get the following errors.
There seems to be an error in the code below.
It was tested with...
Hello !
I have found that error free decryption ( MIC error) on fly depends from S1LEN configuration value.
S1LEN have valid range value for each radio mode
2Mbit 1...
I'm getting an occasional NRF_LIBUARTE_ASYNC_EVT_OVERRUN_ERROR, it often takes over 24 hours to reproduce, and the libuarte appears to be generating garbage after the error...
Hello Sirs
I am using NRF5340 chip in my custom board to use the BLE radio and uart hard ware at the same time. The sample code which has been used for this purpose is ...
I have a BLE device with a MIC, which collects voice data and coded to BroadVoice 32k.
So I want to design a central to get this voice data.
What I think is use 52840...
Hi,
Why do all of these AT instructions fail?
1.AT%XPRODDONE=0
2.AT%XPRODDONE=1
3.AT%XRFTEST
4.AT%XEMPR
Thank you for all your assistance. Kind regards, Peter...
