I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
This is really bad, I downloaded the latest 1.7.0 SDK to the machine and could not build any application (including examples) Always appear errors
Create a GPS.Emproject...
Hi,
I have nRF9160 DK:
PCA10090 v0.8.3
modem firmware 1.2.3
The specifications says that the minimum consumption current is 7µA. So I flash a hex file which shuts...
(Using nRF Connect SDK 1.5)
I have the setup so far that partition manager is aware of the external flash and creates a single partition for it. The documentation section...
Hi nordic
I am using 52832 with sdk15.3:
when I program the hex with sd+APP+bootload, it works fine, while after the first ota, it will get the NRF_ERROR_STORAGE_FULL...
I have an encased nRF52840 dongle that is visible to nRF Connect. However, when I try and select the displayed device I get the following:
I cannot press the reset button...
Hi,
1. What modem versions does this board support?
For example mfw_nrf9160_1.3.0？
2. This board programmer this example:lwm2m_client
Using AT + CFUN? No return...
Dear Nordic team,
in our multiprotocol (BLE, ZB) application ( nRF5 SDK v4.1.0 )we are facing following severe issue relating to the ZBOSS stack: When a router leaves its...
Hello sir/Ma'am
I am working on a project in which i am using some BLE peripheral devices, an Central device and an Android app. I want to get data on android app from central...
I'm trying to program nrf9160 but getting an error due to readback protection.
I have tried the following commands:
nrfjprog --recover
nrfjprog --recover -f NRF91
...
I set an NOPULL type input GPIO, and I found that if I put in a voltage of about 1V,
the nrf52832 will produce a current of about 30uA,
I want to know why it can be happen...
HI
I have using nrf5340 DK for the past 7 months. Sometimes, The DK gets powered up only after 2-3 minutes after giving the power supply from the PC. Even after powerup...
I'm working on a project based on nRF52840 and nRF5 SDK16. I'm using BLE with softdevice S140 7.0.1 and USB CDC ACM for communication with a USB host. Ultimately the problem...
Hi,
I'm trying to run ble_app_blinky_pca10040_s132 on Fanstel BT832 custom board with no success. After writing/verifying the app using the SES it jumps to 'unknow function...
Hello,
I have a question:
i want to send a JSON payload using the PUT-method from CoAP. For this I am creating my JSON Payload with the following function:
The main...
