Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hey all! So I'm working on some custom boards using the nRF52810-CAAA chip, I write firmware using SDK V15.2.0 (outdated I know). I'm having an issue with a recent batch of...
I've been struggling to track down excessive power consumption on a nRF9160 device and have found that, when all UART/Serial are de-selected/off, adding or commenting out...
I want to modify the asset tracker application, for that I copied the 'asset tracker' folder from 'ncs/v1.4.0/nrf/applications' to a folder outside the ncs directory. Then...
I am trying to add a characteristic and am getting error 7 (invalid param). I started out calling sd_ble_gatts_characteristic_add() directly but I realized that characteristic_add...
Problem:
I am trying send samples from SAADC to the NRFconnect app at 1kHz. I have built my application on the ble_app_uart__saadc_timer_driven__scan_mode example . I have...
Chip: nRF52832
SDK: 15.0.0
SoftDevice: S132 6.0.0
IDE: IAR EWARM 8.30
I have a peripheral-role application with __ICFEDIT_size_cstack__ = 0x800 (application call stack...
Hi Nordic:
I know mesh LPN can receive messages from it's friend node, that means when any other nodes send messages to LPN unicast address, LPN's friend node will buffer...
I have developed hardware utilizing an nRF52832 and am developing a bootloader for the system. I have had success following two tutorials: Getting started with Nordic's Secure...
Hi,
I'm trying to print a float over UART but I think the NRF implementation is faulty. I've tested not UART SDK example with the following changes, inserted at line 168...
I have a Thingy 91 and try to analyse the PSM and eDRX in asset tracker application. I use NCS 1.4.0 in this case.
In prj_thingy91_nrf9160ns.conf file I found the settings...
I have: nrf51822 bluetooth module, STlink V2, Keil, segger studio, nrf51 sdk and softdevice files.
I have achieved making the led blink at a ble peripheral device by nordic...
Hi,
I'm using nRF52840 with nRF5 SDK 16.0.0 and Mesh SDK 4.0.0.
I'm trying to add PB-GATT service to the ble_app_uart_coexist example. I set MESH_FEATURE_GATT_PROXY_ENABLED...
我正在执行ble_app_uart_c例程的功率测量，并且已经关闭了串行端口，这与打开串行端口时测量的波形不同。 我猜封闭的串口会影响扫描。
This is the waveform without closing the serial port
This is the waveform without serial port...
I add a compiler flag --wchar32 i n the Misc. Controls section of C/C++ to support character pointers with 32-bit width. But got errors as log attached. Any help is appreciated...
