I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi everyone!
I am trying to implement the OTA - DFU in my project. I have my own board with a nrF52832 chip.
The project was build using SDK 13.0.0 and softdevice s132...
Dear Nordic Support Team,
I was using the CoAP and MQTT components in nRF5 SDK v16.0 .
So my device was able to do CoAP and MQTT via BLE 6LoWPAN. Adding a BLE service...
I am following the turtorial in the Github and build a project which add a custom service. The project can read, write and notify between the board and mobile nRF connect...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board.
I am using the UART module and associated UART drivers.
Is there a way to ignore the...
I have two nRF9160 DK boards that are programmed with modem firmware version 1.1.1 and are using V1.2.0 sdk software. They also are both programmed with the same mqtt_simple...
Hello,
I want to to configure mesh proxy node and along with that it should also contain relay functionalities using nrf5_SDK_for_Mesh_v4.1.0_src.
Is there any sample...
I'm seeing some issues I don't understand when using RTT. Here is a short fragment of code around the RTT_Write statement.
The commented out statements are included while...
I am using nRFConnect with nRF52840 Dongle. Since the last update to SoftDeviceAPI v5, nRFConnect cannot connect anymore to this specific devices (cheap JDY-10 BT/Serial adapters...
Hi, I want to store some personal data through flash in the LPN mesh routine. I read some posts and can be implemented by using flash manager, but I can't find the relevant...
Hello, I am working on storing words to flash using fds. I am working with the nRF52 DK and SDK V15.2.0. As mentioned in my earlier post , I am storing some critical state...
Hi,
Greetings!
I am using below setup:
SDK: v16.0.0
Mesh SDK: v4.0.0
Application: Light switch server and client
Hardware: nRF52DK
Distance between client and...
Hi, I am using ble_app_uart example for peripheral device and it will be powered by a 3.7 V battery. I need to use battery as long as possible. So I decided to make peripheral...
When I put the device into sleep it draws app 30 uA in sleep mode. Read in the manual: "Core standby current= 50 μA", "Current drawn if HFXO is forced on through for instance...
Hi,
I am trying to emulate a vendor's tool, whose BLE properties are configured as follows: Custom 128 bit Service UUID like XXXXXXXX- 0000 -XXXX-XXXX-XXXXXXXXXXXX
Custom...
