Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi,
i'm using SDK11 with NRF52832
After a pin falls from HIGH to LOW The GPIOTE_IRQHandler calls a function in my program to read 8 bits from the bus (Inside the interrupt...
Following the seminar today I tried to build and run this example.
built on command line using west (non-secure nrf9160-DK target)
in a continuous loop I get
```
SPM...
I want to dump lengthy log data out through an RTT connection if the JLink is connected but NOT spend that time if there's no physical RTT channel present. The idea is that...
1.Customers need to use nrf52833 for design and production in this package: WLCSP package, 3.175 x 3.175 mm
2.I noticed the description in this manual:nAN-38 WLCSP Handling...
At present, the SMS is sent normally. The format of nrf9160 is 7bit, and can send a maximum of 160 characters. However, how to send it in packages if the content exceeds 160...
We are looking for a Bluetooth 5.1 indoor positioning solution at precision around 1m.
Could you help figure out which platform/reference design is capable of implementing...
Hi,
I have configured the MQTT simple sample from nordic to send data to our broker, this works just fine at the moment.
I would like to send Json formated data to the...
Hi all,
I was playing around with radio and trying to create interupts for the event_end flag and i've now messed up completely and even without the code i added the chip...
I am working with the PWM driver to drive a stepper motor and I have a couple of doubts about when all the events are generated. My doubts are related to events:
NRF_PWM_EVENT_SEQEND0...
Hi,
I try to implement a disconnection after wrote a characteristic parameter. This byte change the working mode of my systeme.
So user connect, write the field to change...
Hi everyone,
I'm working on a BLE application using nRF52840. This application actually run with nRF SDK15 and we need to upgrade it to SDK16.
I followed Migration guide...
Hi,
We currently have a project that uses nRF52832 in audio. There are currently two questions that need to be confirmed.
first question:
Because other chips on the...
Hi,
The Ai0, and Ai1 inputs can be used as voltage references for COMP feature. Is there a way to use input Ai0/Ai1 as reference voltage for SAADC?
Thanks in advance...
Hello! I need to migrate the loader project from SDK15.3 to 16.0. The SES project parameters are as follows: FLASH_PH_START = 0x0 FLASH_PH_SIZE = 0x80000 RAM_PH_START = 0x20000000...
On a custom board based on nrf52840.
We want to write data on a SD CARD every XX seconds.
We implement this by changig the state of a state_machine at every wakeup from...
