Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hey all,
So I am a beginner and haven't work with this environment a lot. I use SES to debug and upload application to the nrf9160. I can allready upload some basic application...
Hello, I have three nrf52840 development boards and one pcb that I made myself using nrf52840. I want to find the location of my pcb with a demo using these development boards...
Hello,
Softdevice: 7.0.1, SDK: 16.0, Device: nRF52840
In the production, we want to save time programming the devices. So I'm using following command to combine bootloader...
Setup : I am using android-ble-library for my android app. I am using modified blinky example on embedded side. I have tried following implementation on android app:
I...
I have two nrf51822 devices, one running s110, the other s120. The s110 device reads ADC values every 20ms, and if they changed from the last reading it sends a notification...
Hello,
The following define is present in file nrf_sdm.h, SDK 17.0.2:
#define SD_FLASH_SIZE 0x26000
I think it's wrong, it shall be 0x27000. But it's maybe not used...
I am working with a IC that requires SPI clocks to be synchronized (in phase) with its system clock. Currently the IC's clock source is connected to one of the nRF52's GPIO...
problem: in BLE data length negotiation , In the response from slave tx doesnt go above 216 , and rx doesnot go above 54 .
s140
Experimental UDP example - sdk v16.0 (...
Hi.
I'm pretty new with SEGGER Embedded Studio and with nRF9160 dk.
I would to receive time with NTP serveur but I'm lost.
I don't know what to use. if it is better...
Hi, I am working on nrf52840 and I am trying to enable the repeated pairing attempt protection. (PM_RA_PROTECTION) After enabling the module I can see the logs telling me...
Hi All,
I want to create a Thread network with multiple OTBRs, which is based on two nRF52840 run Thread RCP hex provided by Nordic SDK.
I created the thread network by...
Hi there,
I would like to set my dongle into DFU mode from software, I am using the USB-CDC-ACM class, and the softdevice as a central device.
Ideally I would send a...
Hello,
in our project we have a nRF52840DK as central and a nRF52832 chip on a custom board as peripheral. The software on the nRF52840DK is based on the ble_app_uart_c...
Hello
I use mpu6050 and I want to use a 'Complementary Filter' to get the angle of the X, Y, and Z axes.
Applying this filter to the value of mpu6050 seems to reduce...
Dear all,
Greetings!!!
I am using the NRF24LE1E module. I want to pair my device with host using a button. Button is available on device side. Please help me to do it...
