Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I am writing a code to blink the LEDS , the 3rd one is not turning off.
Here is the code-
#include <stdbool.h> #include <stdint.h> #include "nrf_delay.h" #include "boards...
Hi,
My device is using nRF52840 with s140 of SDK v16. BLE feature is used with SD .
Sometimes application hard faults in SD are observed in devices deployed. It is quite...
Hello,
I find that after I DFU a new application (using the nRF Connect Mobile App), my device boots into that new application and reconnects to the App, as expected. Then...
Hi,
I am using nRF51822-CEAA with S110 SoftDevice on a custom board which is commercially deployed now. I am using IAR 7.80.2 and Segger JLink Ultra+. I found there are...
Hi community ! I saw a lot of topic about that but i'm working with SDK_Mesh_v4 and i don't get what i want. Does someone have a working example of sending string over Mesh...
Hello!
I have a rather vague question and want to apologize for that beforehand.
I was wondering if it is possible to connect a JPEG camera to the nRF9160 DK (i.e https...
Hi, We are in the production phase of our development, and inadvertently , the mcuboot bootloader set the DCDC on a few units. As described here, https://devzone.nordicsemi...
Problem with setting two uart on pca10040 board
hello
I am reading the log by teraterm by connecting pca10040 board to PC via USB.
I am trying to connect 6pin and...
We are using manufacturer specific data to broadcast data at 10Hz.
We're about to do some testing to evaluate different adverting and scanning parameters to find the best...
Many of the sdk_config.h examples have both NRFX_FOO_ENABLED and FOO_ENABLED defined.
So, imagine my surprise when I change, say, NRFX_TIMER3_ENABLED to 1, still get link...
Hi, is it possible to measure NRF52832 vdd voltage using LPcomp. I know I can do it with ADC but it draws a lot of current. I'm thinking if I can compare VDD to lpcomp reference...
Overview: number of bytes sent by ble_app_blinky at notification is determined by (note my changes for debug:
in ble_lbs_init() of ble_lbs.c and not by:
in ble_lbs_on_button_change...
I aam badly stuck in this error and dont know what to do with this i have downloaded ble adc scan mode example and running it on sdk17 using SES .i have removed powerclock...
Hello,
I have Thingy:91 connected to the cloud. I see that data is send correctly in json format (on nRF Cloud terminal). Is it possible to plot graph or download csv file...
The modem on the nrf9160DK (modem fw v1.1.0) appears to get stuck in searching mode. It doesn't happen all the time, and I was able to create it with the following AT commands...
