here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
We are trying to install the nRF toolchain/SDK/SES etc. so that we can compile (modify for NB-IOT) and evaluate the nRF91 asset tracker.
We have followed all the steps...
I am trying to use a button to put the nRF9160 to sleep and to wake it back up.
I configure my button as follows:
gpio_pin_configure(dev, PIN, GPIO_DIR_IN | GPIO_INT...
Based on mesh3.1 sdk15.2 Can I add DFU service to light switch server? Used to upgrade firmware via APP nrf Connect? I added a dfu service to the light switch server with...
Hello,
I wrote the code for HT1632 using SPI Protocol
while debugging when it comes to below function it will stop debugging
HT1632_5X21_init( LED_MAX_DISPLAY_X, LED_MAX_DISPLAY_Y...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
Currently with one device...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I am using FDS module to write into Flash. I...
Hi there,
I' d like to develope dfu by receiving byte stream (mimeType) over USB or UART
I am almost newbie for developing dfu.
I already checked dfu over ble and...
Dear Nordic,
I try to compile the Keil project inside the thingysdkv210.zip file but it does NOT work.
I use Keil uVision V5.24.2.0 on Windosw 8.1.
There are so many...
Hi,
the evalboard seems successfully implementing the command start_rx_sweep by placing the receiver in the sweep mode.
infocenter.nordicsemi.com/.../nrf_radio_test_example...
Hi,
I am trying to connect with nRF9160-DK to our local network. After first restart of the device I was able to connet to the network, but straight after that Asset Tracker...
Hey, I am trying to incorporate an app timer using the app timer function already on the code in the central and peripheral examples of the SDK for the UART examples. Specifically...
Hi Nordic,
I have old NRF52832 product which is developed by SDK11.0. The bootloader start address was set to 0x79000. Now We want to upgrade the it firmware by using...
Hi,
i'm using BLE MESH 3.0 Light Switch Example code. i want to send Light on-Off command every 2 second Timer base instead of Button press.
i got an error below.
Hi,
I am trying to develop the interactive_pyaci serial interface so that it can restore itself once it has been closed.
To do so it would be useful, once the db is loaded...
Hi,
Current github repo of IOS-nRF-Toolbox doesn't support X-code 10.2. Is there an update coming or is there a work around so that we can build app for ble-uart application...
