Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello,
I am developing an application using the nRF51422.
For flashing and debugging the nRF, I use a ST-Link V2 debugger which uses SWD. The IDE I use is uVision.
I...
Hi
I have been succeed test SDK15.0.0 i2s example and got UART data.
UART started.<CR><LF> NRF_LOG_DEFAULT_BACKENDS_INIT started.<CR><LF> NRF_LOG_DEFAULT_BACKENDS_INIT...
Dear Sir,
I am working on SDK15,nrf52832 and soft device S132.
I was working on the following scenario.
A peripheral device advertise as soon as it is switched ON. ...
Hi, nordic
I get some problem when developing the ancs with SDK15.0.
I run the demo with ble_app_ancs_c on the board of PCA10040.
First of all, after my iphoneX (system...
Hi all, development software: nrf5_SDK_for_Mesh_v2.1.1_src\examples\light_switch\proxy_server Board 1 nrf5_SDK_for_Mesh_v2.1.1_src\examples\serial Board 2
IDEs: SEGGER...
Hello,
I am using NRF52832 boars s132 and sdk is 13.1. I have developed my application is read analog accelerometer valie and send to mobile apps. Now i want to also battery...
I'm facing one issue while uploading firmware using BLE DFU.
Details:-
Hardware : NRF52840-DK
SDK : v15.0.0_a53641a
IDE : Segger Embedded Studio v3.40
Mobile App...
We have a Сustom BLE device and observe inconsistent behavior when connecting from this device to to nrf52dk running different SDK versions. - Custom Device connects OK with...
Hi All,
I'm trying to use the nrf52832 as the SPI master to get sensor reading through spi from another sensor. I want to base my firmware on the spi_pca10040 example but...
How can i sample nrf52 own input voltage to do battery measurements?My nrf52 chip is directly connected to a battery and it needs to sample its own input voltage without a...
I have been searching through the info center and can only find the slightest mention of the bsp_board functions.
Could someone help me, locate the right page documenting...
hi sir
i have start my project in NRF52-DK development kit but some BLE card give me data in three channel and i have received all data and give me same like data pls find...
I'm new to use nordic. I am using thingy 52. I would like to add a new custom feature that communicate text via BLE from app, store the text as userid in the thingy and check...
