Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello,
First time posting, Here are the details of my setup, I would greatly appreciate any help from anyone at this point. I have purchased 2 nrf52 development kits with...
Dear Sir:
I use ble_app_uart example , i want use pwm to driver the FR Port ,Peripheral load. the Peripheral load is pulled up to battery.
when driver the load ,the...
Hi All;
Just a major concern of mine is that SES IDE is so inconsistent;
I can build a solution get errors and warnings...
Without editing anything and rebuilding the...
I have an issue with my board. It resets occassionally itself. When the board is starting by debugger and when it resets itself I can read 0xD in RESETREAS register. What...
hi,
I tried to provision the light example using the nRF Mesh app.
So far, I succedded in provisionning the device but i couldn't set the publish suscribed addresses,...
Hi, I'm using a modified version of the light_switch example to control a RGB led on Mesh SDK 2.0.1. I already managed to control the led by using 3 variables for each color...
I'm designing a Printed Circuit Board (PCB) for and embedded system currently in development. I am using a BL652 DVK from Laird and using SWD programming with Keil uVision...
My project is using QT program and nRF52DK borad.
I want to UART communication with QT and nRF52DK.
#1. If i write "hello" in qt program like below...
===========...
I saw this post for SDK v12.2:
The FDS requires data to be word-aligned
devzone.nordicsemi.com/.../how-to-force-word-alignment-for-fds
Is that still true for...
Hi,
My target is to update the application firmware running on the nRF module using serial wire connection.
I currently do experience the issue, that DFU process completes...
I am in the initial phases of porting an arduino project using the NRF52832 to the Nordic SDK (14.2 for the moment) and am running into issues when using TWIM and an event...
Hello
Im trying to figure out where the health model client sends the health messages. Ive tried doing prints in all of the send methods in health_model_client.c but not...
Hello,
I'm having an issue when I try to connect to my device from an iPhone X. I'm using SD132 v6.0.0 on SDK 15.
The phone tries to connect and then it times out. All...
Hi!
After connected and get log info "Connected." I start bonding:
but there is no any success message.
Therefore nRF52 SDK15 can't to made secure bond.
Why?
