Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I am about to start development on a project that will be using a pair of nRF52832's to make a low data rate connection between a PC (with a nRF52832 based dongle) and a device...
In the event that a Nordic soft device library call fails (as determined by APP_ERROR_CHECK() macro) and our application level app_error_fault_handler () function is called...
Hello,
Ported my FreeRTOS application on NRF52 from SDK 12.2.0 to SDK 13.0.0 .My application is using freertos apptimer for timestamping and waking up of device which was...
Hi,
I am trying to run a ble mesh example but I prefer to work using keil, because I already worked other examples using the SDK (12, 13 and 14) and PCA10040/PCA10056 nordic...
For a precision timer application I have an external temperature compensated RTC (DS3231) which produces a highly stable 32 kHz signal connected to pin 5
When I associate...
Hello,
I am rather new to BLE and the NRF5x.
I want to build the following application: a swim timing sytem. The system consists of master timer with a high precision...
Hey,
I have a few questions about dynamic multiprotocol BLE/Thread support.
1. Multiple BLE connections. If I have one connection and connection event length is set for...
I'm working on a bootloader using the /examples/iot/bootloader as an initial template. The image to flash is stored on SD card. I'm at the point where I am successful in writing...
Hello.
i setup - BLE Stack + Uart 1 + SPI 1.
Infinite loop inside nothing code.
nRF52832 consumed 5mA + a.
and i add power_manage() in Infinite loop.
Nevertheless...
Hi,
We are potentially considering using nRF52 DK in our projects. Kindly advise on following questions,
(Q) How we can use uC/OS-II or uC/OS-III with nRF52 or other nordicsemi...
Hi,
I am testing the experimental_bootloader_secure_usb example.
I have confirmed that the old v0.9.2 board has been replaced with a new board and connected to the ...
HI EVERYBODY
The SDK14.2.0 ble_app_uart' NRF_LOG_INFO() fuction can not printf data.how to make it work? i modify the sdk_config.h file as follow,but it still not work....
Hi,
I’m facing a strange problem regarding nrfjprog
I used it for many times without any problem
Now I’m preparing a VBNET app to program a flash sector of the nRF52832...
Hi,
I have my application running on NRF52 using NRF SDK11. I want to upgrade the application to latest SDK14 and also softdevice to v5.0
The application uses following...
Hello,
I am an electronic engineer student working in a company for my graduated internship.
I would like to know the longevity/lifetime of the nRF52840, nRF52832, nRF52810...
