Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Dear Community,
We want to use bonding to connect our app to the nRF and create a personal account.
So all your devices will have the same UUID. If the device never connected...
We're working on a board with an nRF52840 running BLE with softdevice S140 and SDK 17. The board has an external SPI flash, and when we realized that SPIM3 can be run at higher...
I want to know if I call the following function, which condition should I meet to determine that the coordinator is not connected to any terminal devices. For example, I now...
Hello, I am looking for some help or example code that describes minimum set of the files and #defines required to enable AES 128bit encryption and decryption using ECB mode...
Hello,
I'm trying to learn what might be typical latencies for Bluetooth LE Audio. For instance, the aptX low latency codec claims latency around 20-40ms. Is Bluetooth LE...
Studying the documentation for the nRF52811, I found a difference in the description of memory recording and memory erasure:
write: " The CPU is halted while the NVMC is...
Hi,
I have nRF52840 DK and am using nRF5_SDK_17.0.2_d674dde.
I am not using SoftDevice, and Zephyr RTOS.
I have a simple program and using RTC0 timer. My code snippet...
Good afternoon,
I have a question regarding the nRF9160 and the eSIM configuration. We have developed a prototype PCB based on the nRF9160 DK and included an eSIM. However...
Hello,
I am trying the example of ble_app_uart and when i am building the example it gives me an error RX_PIN_NUMBER undeclared. When i load the pca10056.h i can see TX_PIN_NUMBER...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b and FreeRtos
This device has some bindings already set...
Hi,
my zigbee network for 120 sensors. if i declare 120 install codes then most of them don't work. The "zb_secur_ic_add" function works without error, "zb_secur_ic_get_list...
Hello!
Following problem:
I try to save 100Byte uint8_t messages in the nvs on the nrf9160.
Sometimes it works and only some moving logs come up and sometimes the following...
Hai
I have a requirement to download the FW application of NRF9160 M33 via serial UART. Is this possible?
So, which zephyr project am I to consider for reference?
...
Hi all,
looking for samples for using CoAP with DTLS 1.2 (PSK) on nRF9160. All the samples I can find are not using DTLS. Highly appreciate any hint!
Thank in advance...
