Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I am using Nrf5340 with “Direct test mode” example.
I try to make my nrf5340 kits to be an AoD receiver under the DTM.
Now,I am able to run the example code to...
Hi,
I'm using spim on nRF52810.After I init the spi driver and using APP_ERROR_CHECK(nrf_drv_spi_transfer(&spi, &Command, 1, m_rx_buf, 1)) , RTT Viewer showing FATAL ERROR...
Hi,
Is there a way to control the 1Mhz BLE symbol clock?
We want to use nrf52840 as a GFSK transceiver and we need to control the symbol clock (up to +- Khz resolution...
Hi,
I'm running into issues where iOS is caching the handles. I found out that I need to set IS_SRVC_CHANGED_CHARACT_PRESENT to 1.
But where should I do that? In sdk_config...
Currently messing with the NRF52840 chip and given examples (NRF Connect SDK v1.7.0) on two different eval boards (the nRF52840-DK from Nordic and the BMD 340 Eval board from...
Hi,
We need detail understanding on Mesh performance testing and all the tests involved in testing BLE mesh communication,
can you please share detailed information...
Hi,
I currently got the DFU mode working with my nrf52832 while it is being connected to the PC using the Particle Debugger.
I use the GPREGRET method and while connected...
Hi,
In nRF52840-QIAA Reference Layout 1_1.zip, nrf52840_qiaa_var5_schematic. pdf: are C3, C4, C22 and L1 inside or outside an RF shield?
Thanks,
Mark J
Hi Elfving,
the previous ticket find under the following link is locked. So I decided to start a new one.
https://devzone.nordicsemi.com/f/nordic-q-a/80063/bluetooth-mesh...
Hi all,
when I program Hello World sample to my own customized board base on nrf5340, no prints at all. is there any thing I missed?
when I program the Blinky sample to...
I am trying TCP program in nrf9160, in my prj.conf If I set CONFIG_LTE_LINK_CONTROL=y then it is giving CMake error,
if I make CONFIG_LTE_LINK_CONTROL=n then it will not...
Hi all,
I am trying to use an interrupt callback handler but I can't get it to work. I got the interrupt initialized but whenever the callback is triggered, the system...
Dear Nordicsemi Developers,
as the latest Zephyr LTS v2.7 has just come out for a few days, we are considering updating our firmware base SDK to a newer version. So we...
