Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I am offloading sockets in config. I instantiate a socket, set the send/recv timeouts, and then call connect(). It's returning a 95 which is EOPNOTSUPP. I was able...
Hi,
I'm investigating firmware image signing on the nrf9160 using MCUBoot and the nRF Connect SDK v17. I have configured
and it seems to work via `west build -b nrf9160dk_nrf9160ns...
Due to parts shortages, we are having to scramble to find compatible hardware for our project. I have sourced some nRF5340 modules but need to know if Gazell is supported...
Hi!!
I am facing an issue wherein more than one device is acquiring the leader role in a same thread network.
In my setup, I have a total of 4 devices. Three of them are...
Dear Team,
I have to use many number of pages to store data in flash memory in nrf52840 , but I am confuse that what will be start address and end address in flash_fstorage...
Hello Team,
I am facing segmentation fault while reading the OTP memory using pointer in my code. To write the OTP value I have used below command which was successful and...
Hi,
I received the nRF9160DK yesterday, and used the AT Client to get talking to the modem and connecting to a network. In VS Code I built an application from sample ...
Hi there,
I'm using the product specification of the nRF52840 to program the SAADC in continuous mode using its internal timer. I'm not able to use your SDK. Unfortunately...
We've built a custom board, at power off current is 1-2uA and when connected average current is ~4.7mA. Internal DCDC is enabled, this shaved off >2mA. Other than reducing...
Hi ALL:
- SDK version: nRFSDK 15.3
- HW: nRF52832
I am tried to earse the flash by sg_flash_page_erase(uint32_t page_number), but still failed. My code snippet as...
Hi there,
I want to read the memory from nRF52840,
but J-Link showed me, J-Link is defective, how can I rectify it ?
It's from 2018 J- Link ,
Screenshot :
tha...
Hello,
I'm running the nRF Mesh SDK 5.0.0 with the light CTL LC server example. I have also developed an implementation of a DALI master. DALI is a manchester encoded signal...
I am using: \examples\ble_peripheral\ble_app_uart and \examples\ble_central\ble_app_uart_c .
In Nordic infocenter it says: The application scans peripheral devices and connects...
Hello all,
I would like to know if it would be possible to simultaneously use 3 instances of I2C and 2 of I2C for the nRF5340DK. As stated in the data sheet, the application...
