Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
I am trying to send data from BT840F to ESP32 via UART. Which pins of BT840F shall I connect to the corresponding pins of ESP32? I am asking this because I couldn't extract...
Hi team,
My customer is asking if they can remove L38, L39 and C225 when they change nRF52832-QFAA/ nRF52832-QFAA-G version from DCDC to LDO mode? Any suggestion?
Also...
Hello,
in our product we need to have the possibility to set name higher then 31 bytes.
We modify the code according the tick
devzone.nordicsemi.com/.../sd_ble_cfg_set...
I can connect same sensor using nRF connect app. See attached snap shot.
The BLE connected Pressure sensor is advertising the Unknown Service using UUID : -- 18FF (First...
Ladies and Gentlemen,
I was wondering about the maximum clamping current of the Body Diodes of the nRF9160's IOs. There is no value stated in the product specification....
This might be a naive question, as I am a novice in this field.
I am making something similar to ble_app_hids_keyboard in sdk11, it will be configured as a consumer device...
I am using windows 10 and I was trying to operate my pca10028 board for a blue tooth connection. I pressed the reset button a few times but now its not working and only LED...
Can a corrupted InfoPage of the nrf24le1 be fixed from an ELNEC/Dataman programmer? I have read on the forum that th InfoPage can be restored from Nordic kits/IDEs, but I...
I am using an nrf52832 DK with Zephyr and I have a component that require a block of code to run uninterrupted. Specifically I am using HX711 with four load cells, and the...
Hi,
I want to display a picture with a screen (80x160) with st7735 and sdk 15.3 (segger embedded.)
I have some problems.
I use the function nrf_gfx_bmp565_draw, so I...
I am using the NRF9160 for SPI using an external Flash. After using the 'http_application_update' samples, I was able to get the value of the data written on the external...
Hi, I am a MCU developer searching BLE MCU to develop some IoT project.
I would combine nRF series and LTE NBIoT module for IOT project.
And I need to integrate many different...
Hello all,
I am trying to use my nRF52832 DK for a wireless camera shutter for my phone. I have reviewed the example code from SDK 15.3.0 named ble_app_hids_keyboard as...
Using SES, nrf52840DK, the onboard debugger.
I am able to set a breakpoint and use condition like x == 5.
I am unable to use anything but the == operator. In SES I...
