Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Dear Nordic Engineer
I currently have a project that requires 5340 to act as an MCU. I also need to plug in a FLASH, which is 4GBIT NAND FLASH. Is there an example of supporting...
Hi :
nRF52832 PCA10040 DK burn this link hex code: https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE/Download#infotabs
Can...
https://devzone.nordicsemi.com/f/nordic-q-a/49269/long-range-nrf52840-central-can-t-connect-with-peripheral-in-ble_gap_phy_coded
due to this problem recently I have problem...
Hi Nordic Support Team,
I have asked this question previously, but I might as well make another post to collect my experience with this problem this past month. I will try...
Hello,
Here is my configuration:
NRF52840
S140
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE 247
I would like to enable DDLE in order to get more than 27 bytes in each...
Getting the following build error when trying to build a test program after adding my HDC2022 driver to Zephyr: I think this simply has to do with a linker issue I'm missing...
I am struggling to understand how to use a Soft Device 132 on a BT832 fanstel part. I need to have the uart come out on pin 1 and 2, and have hardware handshaking enabled...
Dear Sir/Madam,
we are trying to send large chunks of data (up to 512 bytes) via bluetooth with notifications with the added difficulty of an arbitrary MTU size. Our approach...
I am trying to update on nRF52 DK board with another, separate nRF52 DK board using OTA firmware updates. Essentially, I am trying to replicate how the nRF Connect Desktop...
hi...
i am using nrf52840 , segger.... mesh sdk 3.1 version in this case i want to send the simple message from client to server .how to do this ?
suggest me an idea ...
Hi,
I have some of peripherals at 1.8V and some at 3.3V that I'd like to run off the nRF5340. Is there a way to selectively set which interface is in a specific voltage...
Description:
We'd like to extend our existing bootloader. It currently supports UART transport and we want to retrofit a bootloader that also supports OTA via BLE. On merging...
I am testing the nRF9160 DK. I would like to know which SIMs are available in Japan.
I have confirmed that Sakura's Secure Mobile Connect SORACOM(Plan-KM1) works.
I'm...
