Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
How can I make the device generate random address periodically? I searched on the forum and found people mentioned BLE_GAP_ADDR_CYCLE_MODE_AUTO when call sd_ble_gap_address_set...
Hi.
I have a product that acts as a peripheral, and bonds with centrals that are typically smartphones. Normally the peripheral uses a whitelist to only connect to bonded...
So I noticed the program goes into a state where it's stuck on NRF_BREAKPOINT_COND , which happens after getting into the following writeToLogger () template function. If...
Hello,
I am evaluating NCS 1.5.99 zephyr's sample"periodic_adv"and"periodic_sync"with two nrf52833 DK. The sample "periodic_adv" runs normally on nrf52833 DK.But the sample...
Hello,
I've been trying to use Zigbee Endpoint Logger for the light_bulb and light_switch sample. But I can't make it work. I've been looking through the quetions on this...
Hello guys, i want to implement nrf5-calendar-example in nrf51822 with SDK 12.3.
This library can use RTC0/RTC1/RTC2. But i have only RTC0 and this RTC0 is for SD (am i...
hello,
if i want to connect to a peripheral device with strongest RSSI. I need to get the RSSI before connecting.
and i know i can get the RSSI from event of BLE_GAP_EVT_ADV_REPORT...
I'm trying to read the values from the DS1307 RTC through TWI. I've established a connection with the device but am not sure I'm using the nrf_drv_twi_rx() function correctly...
Hi,
I'm trying to run the peripheral heart rate service example on a custom board using the internal 32kHz RC oscillator. However, the code hangs when soft device is enabled...
I am writing my own UART driver and having trouble getting subsequent interrupts. The first time I see the interrupt occurs but nothing after.
According to the product spec...
Hello
I'm using nRF910 DK and need to transmit to aws iot core just like the sample aws iot does, but instead of battery voltage I need to transmit gps data.
In sample...
I am seeing very little information. The LTE button lights green but Modem and UICC stay red. I get signal strength but none of the other items in the block; they are all...
I m using The nRF52840 + STM32 with serialization library. My device is set in central mode and i want to active whitelist,
the configuration seems to be applied correctly...
Dear support,
Anomaly 89 of the NRF52832 states that a high static current consumption is observed when the SPIM/TWIM uses EasyDMA and the GPIOTE is configured in event...
