Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi:
When I tested the DFU function of BLE, the upgrade was unsuccessful, and the APP print log prompt appeared to be a CRC check error.
The SDK version I am using is nRF5_SDK_15...
I reference demo1 of PWM driver example in SDK15.2.0, I make myself PWM driver. the official demo1 use pin17-20 as PWM channal1-channel4, but I use Pin9-P12, I modify the...
Hello,
I would like to measure the frequency of a signal and I use PPI, a timer and input capture to achieve this. Here's the configuration :
The frequency of my signal...
Good evening,
I am using NRF52840 board with softdevice S140 and SDK version NRF5_15.2. I am currently trying to compile the ble_app_hrs_rscs_relay example on SEGGER studio...
Hi ! I have attached the PCB design and schematic provided by Nordic for nrf52832 which is said that its also same for nrf52810.
I wanted to use the nrf52810 board for beacon...
Hi all, i'm Duy
I'm doing my thesis project about Bluetooth mesh. My board is nrf52832 custom board which is similar to pca10040. i want to build a mesh network with several...
Hello, I'm able get an updated battery service value on nrf connect using the 15.2 s112 proximity example on the DK using a cr2032. Then adjusted the clock to LF RC and removed...
Hi,
Let's say I have a door lock module without user interface... no keys nor display but with bluetooth peripheral module. The user pays is room via the application then...
Hello,
I would like to know if it's possible to simply configure all parameters for a BLE connection by a PC software.
The goal is to manage the BLE parameters to measure...
Hi,
I want to create 1 hex file that will contain my bootloader, app and softdevice.
I know i can use NRF GO studio in order to read each hex individualy but it is of...
Hello,
I am using PCA10040 development board based on nRF52832, Softdevice 6.1.0 & SDK 15.1.0.
On the Nordic website, I have verified that Softdevice v6.1.0 supports Chained...
What is the best practice for protecting against ESD for unused pins, should I leave them floating or ground them? I noticed in other posts here that it has been recommend...
Hi!
I use HID example and try to understand in a hid service init for why report_map_data[] with a table.
What is do this array? If I use keyboard example, I should get...
