Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello
Is there a possibility to build MCUBoot, SoftDevice, Firmware Loader and Application separately and then merge it manually? Or to build MCUboot + SoftDevice + Firmware...
Hello there,
I am working on a project which involves nRF52840 to scan and connect to specific BLE beacon.
So while scanning, nRF writes scanned data on UART. On same...
Hello,
I'm running SDK v.2.8.0 and developing using the nRF5340 Audio DK. I've successfully flashed using the buildprog.py script, and have set up my DK as an Auracast source...
Hi
1. At nRF5340 datasheet page 420, the PDM duty cycle is 40%~60%, any register can tune duty cycle? Or it's nRF5340 variation tolerance?
2. Since our DMIC IM69D128S...
Hi all,
I'm testing Skylo NTN on nRF9151 SMA DK with the latest pre-commercial/alpha NTN modem firmware (downloaded mid-December 2025).
Registration works fine, and uplink...
I am trying to get the nrf/sampoles/bluetooth/direct_test_mode working together with the code from zephyr/samples/subsys/usb/dfu-next.
I have the DTM mode running correctly...
Hello,
I think there is typo on page 541, in the PWM, Pulse Width Modulation, section of the nRF52840 Product Specification V1.11.
It states "pulse with modulation", but...
Hello,
I have a question concerning the neighbor cell measurement feature on my nRF9160.
After some tests, it seems to be sensitive to the operation mode. For example...
I am currently working with nRF52810 using nRF Connect SDK v3.2.1 , and I am trying to run the AES CCM PSA Crypto sample .
However, when running the unmodified sample, it...
hello i am new to the nrf trilateration and direction tracking using nrf52840, i need some help with the sdk and programming and working examples .
eg : I have 4 nrf52840...
Unable to connect JLink via USB. Installed different versions of JLink without success. Device Manager showns "J-Link driver" under Universal Serial Bus controllers and nrfutil...
I'm using a custom development board and I want to enable timer 0 through the external 32MHZ crystal oscillator. Here is my configuration:
prj.config: # Enable the UART...
I am trying to live capture and analyze traffic on Wireshark. I followed lessons like https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson...
Dear All:
I have a very strange issue that has me scratching my head. I am programming a GPIO to provide hardware reset to an i2c GPIO expanver (pcal6408a). The io expander...
