I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
Hi All! My question is that while using coded PHY is it possible to enable the ACK? In case no ACK receives then retransmission of the same packet to the receiver. Thanks...
I am trying to measure the frequency of the square wave on the ARDUINO_6_PIN on the NRF52840 Dev Kit. It seems like it works well until the square wave goes above 2MHz. Is...
Hi,
I see that in the latest SDK 17.1.0 there seems to be no example for regular UART but only for LPUART.
That made me wonder if there is any advantage in any scenario...
I have an external flash
S25FL132K
I am able to read , write and erase the flash with nrfx_qspi_cinstr_xfer function for 9 bytes. But I want to write more than 9 bytes...
Hi all, I am working on an electronic lock using the nRF52840. Currently it works using Bluetooth Low Energy and the lock opens when a digital key has been sent. (it has measures...
Hello sir,
I am sending the data of 252 bytes through send_notification() at each interval of time but when i send through send_notification() then following error occurs...
Hi,
I am compiling micropython port for Thingy:52. I am following instructions here https://github.com/micropython/micropython/blob/master/ports/nrf/README.md
I see that...
Hi,
I have created an HSL model and it's working fine. Now, I am using a light that has both CCT and RGB control. So, I have both HSL and CTL model existing in the same...
Board ：52840dk_52840
SDK： NCS1.7.1
IDE ：Visual Studio Code
I remap my bootloader partition in my application .overlay file
as
& boot_partition {
reg = < 0x000000000...
Hi,
When i changed NRF_LOG_ENABLED from 0 to 1 in file sdk_config.h returns the following error
1> Linking tdoa_tag.elf 1> E:/gcc/arm-none-eabi/bin/ld: Output/Debug/Obj...
Hello, did you test the working of 100 pairs (Transmitter and Receiver) nrf52840 BLE modules together indoors? If you did, how much data is lost while working together? Can...
Hi everyone,
I use the radio example as my basis. I call the read_packet() function from receiver example. And there is no incoming data, it stucks there. How can i set...
Hey,
I have an app based on the UART central example. I successfully connect and bond to an android and am able to send data via uart over BLE.
I want to send data also...
Hi
I am converting libraries MAX30105 Arduino to nRF52840, but I have a problem,
"MAX30105 parrticleSensor;" what is it?, how can I to convert this? is it a variable?...
Hello , I am trying to build the bootloader source code provided by Adafruit for its nRF52 core. The project is based in Segger Embedded Studio.
Adafruit's nRF52 core bootloader...
