Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
We're working on an nRF52840-based project that started development on SDK 17.0.0 and Softdevice S140 7.0.1, but we wanted to get it to the latest release before production...
Hello,
I am working on Arduino's platform and decided to ditch the ArduinoBLE.h library due to its overhead.
I would like to send high frequency (2Mbps per the spec ,...
Hi,
I've trying to get the Omnivision OV7670 to work with the nRF52840-DK. I'm not completely sure whether I've configured it correctly. My pin assignments are adapted from...
Dear,
we have found a strange behaviour when using the DTM in SDK 17.0.2 and 17.1.0. The problem starts from ble_dtm.c:1188 when comparing the parameter value with -30dBm...
Using SDK 14.0.0 with SD 132 v5, the device name I'm advertising with here is "000000DK". But the advertising module is truncating it to "0000". It will do this if I have...
Hello,
I want to use 1M baud rate in nRF5340 DK board.
DK board is connected to USB to Serial.
Until 921600, UART is received correctly. And UART is broken in 1M....
Hello,
I have been using NRF Connect SDK 1.6.1 with Microbit V2 to run some zigbee projects! Now when I should build some new firmwares I upgraded to SDK 1.7.1 and after...
Hello, I have an nRF52840 custom board and SDK 17. I want to make a project with a buzzer control. I am trying to find a suitable sample project to start developing my own...
Hi everybody,
I am working with an UART example with multi-link and everythink working on coded_s8. The objective is keep 20 devices connected and every peripheral send...
Hi Tech support:
I am using the latest Desktop nRF Connect(Windows version) tool. And I want to use it to connect to my nRF52 DK board and setup up an advertising setup...
Hello,
for our application i need to periodically enable and disable the openthread stack on the nRF52840 chip.
For testing purposes i've modified the Thread CLI example...
Hi,
In my application i am trying out to transfer data in Long range BLE_GAP_PHY_CODED mode , i have set my peripheral has to advertise in PHY coded mode below is the advertising...
Hello,
We are using nrf52832 in our development, we recently got the otii arc to measure the power consumption of our device.
During sleep mode we notice a huge spikes...
This should not be very hard (beginners question), I want to convert an array of characters to an integer, I added string.h but it is not working with the function strtoi...
