Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi，
sdk：ncs v1.6.1
board:9160dk_nrf9160
I use RTT to output log data, but I found that it can only output about 1k characters each time. Where can I modify it?
this...
Hi Team,
These are the SDA and SCL lines of nRF52832 connected to a sensor. the clock frequency defined in the code is 400 KHz, but its coming as 200 KHz on oscilloscope...
Hello, I have designed a custom hardware using nRF52833. I tried to program the nRF52833 using nRF52832DK, I am having following connections- nRF DK nRF custom board VTG-VDD...
Hello,
I have applied for the SUPL license and it got denied. I met the criteria which is mentioned by the Nordic.
I did log in the last 4 week and I am the member of...
Hi,
I'm trying to register the SIM card that came with the nRF9160-DK I just received and during SIM registration, it's stuck at the "still working" step indefinitely...
I have custom board with nrf52833 Soc. I was trying to implement WS2812 LED driver in zephyr which connected to ( P1.09). according to WS2812 Sample Application I copy the...
Hi all
Thanks in advance for any hints you could give on this. I would like to measure two pwm signals (frequency and duty cycle) on two input pins of the nrf52832.
board...
In the nRF5 SDK there are two uart drivers, UART and UARTE. The UARTE driver makes use of the DMA whilts the UART driver uses interupts. This is what I understood when I used...
I am considering using this part from MAXIM (MAX31343).
https://datasheets.maximintegrated.com/en/ds/MAX31343.pdf
it is an RTC plus a 5ppm oscillator output that I can...
Hi all,
Now I'm analyzing the bug that is the fault of my application's timing control.
On analyzing, I found the difference that garbage collection callback was delayed...
Hi,
I am using nRF 5340DK borad, trying to flash Direct test mode sample "nordic,nrf5340-dk-nrf5340-cpunet". My aim is the enable direct test mode on the nrF board in order...
I'm using 3 nRF52840 DK borads (provisioner,light_switch_client, DFU). I set DFU (DFU example used) as target board and connected it to PC as serial interface. I have provisioned...
Hai,
I'm facing some difficulties in programming FOTA over UART on the NRF9160 board.
Currently, by using the following command I'm trying to push the bin file via UART...
Hello Team,
I have a small issue but troubling me since a long time now. Accidently my debug terminal and project explorer came out from their original positioning. Now...
