Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi ,
There is an error when to debug the nRF52840 target board by the PCA10028 board(as error information).
(pls note, There is running okay when to debug the nRF52840...
I have an nRF52805-based BC805M module from Fanstel. I need to control it from an MCU over serial/I2C/SPI to implement Bluetooth profiles like BIP and FTP. I prefer canned...
Hi,
I have two sets of hardware, one is nrf52840 DK, and the other is my own board. I use the same program, update package and mobile phone. When using nrf52840 DK, the...
I am using below base example on my peripheral device to send a string over BLE to a central device:
\examples\ble_peripheral\ble_app_uart\pca10040\s132
I use function...
Hi,
I am working on a custom board using an nRF52840 and developing with SDK5 (V17.02).
I have a serial communications channel to the device which must use UART as I need...
Hi,
sounds odd but is not, I try to run samples and my own project on a nano 33 ble, and with the first upload of blinky it seams that the system start and crash (ttyACM0...
Hi!
I'm developing a custom PCB with a NRF52840 which I made a custom firmware based on ble_app_uart example. I test my product with different phones, Android and Apple...
Hi.
I am developing PCB where there is a Wifi module ESP32-WROOM and a nRF52833 connected via 2-wire UART interface (TX/RX only), there is no way to use 4-wire UART because...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hi!
When opening the LTE Link Monitor in nRFconnect 3.7 under Linux (Ubuntu 20.04) only a "whitescreen" appears after I select the device. The application is not visible...
Hello,
I am using NCS v1.5.0 and would like to check is a KMU slot is being used or not. I erased the whole SoC and tried reading the directly the registers, in secure mode...
which pins can be used as PWM output pins in nrf52811.
Can I use them directly or I need to add some hardware to use the PWM feature.
I have an NRF5811 SOM (EYSNCNZWW...
Hi Sir/Mdm, I want to use 1.54 inch e-paper module from waveshare with nRF52840 dongle with Zephyr RTOS. I have read the documentation from Zephyr about the display and noticed...
Hi,
We use the nRF52840 and have now run out of space using debug mode compilation (using CMake from bash).
When we compile in release mode, we get 50% full flash, so...
