Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I am following the Getting Started directions here: https://www.nordicsemi.com/Products/Development-hardware/nrf52-dk/getting-started#infotabs
Steps 6 and 7 do not work...
I am currently using the power profiler kit ll to see if it is suitable to run power consumption tests in our automatic test system. I am using the python API from https:...
Dear community,
I'm using BM833A chips which contains a nRF52811 nordic chipset. I use a S140 softdevice, for both, beacon sender and central.
I have configured both to...
Dear Sirs,
SDK: NCS version 1.6.0
Board: nrf5340 DK
IDE: SES Nordic Edition V5.50c
Compiled in application core cpuappns
I am a beginner with nrf programming...
Hi all,
we use nRF Connect for Desktop Programmer tool for flashing nRF5340 at production plant. Our Regulatory Affairs & Quality Assurance dept. is asking for a validation...
Sometimes the Power Profiler App does not display the average current and charge values for the Window (see screen capture, below). The values are displayed while the capture...
I'm working on a program using the ble_peripheral/ble_aapp_uart project. While testing the program, it was confirmed that the connection was disconnected after 1 minute 35...
Hi ,
I tried to use the sample code of central and peripheral project "ble_app_hrs_rscs_relay" , to add a new service to connect with light and button peripheral by "lbs_c_init...
Hello,
we are developing a PCB with a nRF52840 in normal power mode. I know that VDD and VDDH have to be shorted in the normal power mode, but due to a layout error we have...
when debugging peripheral_uart sample in ncs1.5.0 used nrf5340dk board , a error produced in function static int bt_init(void)
static int bt_init(void) { int err;
err...
I am trying to use nrfjprog.exe (for the first time) to see if my code is being corrupted on a power fail. It keeps returning an error that I can find documentation on.
...
Hi,
We bought smart watch from company xyz. Watch is running using Nrf52840 and supports buttonless DFU. we are customizing the smart watch firmware as per our requirements...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
My device is a peripheral. I want to connect with two smartphones. At that time, I want to connect under the following...
Hi, Could you provide source code of nRF Sniffer for Bluetooth LE firmware?
https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE...
