Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
This is the second time I am posting here related issue on nrf52832 SPI communication. I am still not able to get the response from the sensor. Here I am testing my SPI is...
Hello
I'm going to use the GFX example of sdk v17.0.2 to running the ST7735 TFT LCD display.
I am using Adafruit's 1.8-inch (128*160) display and testing it on the nRF52DK...
I am learning and testing the FOTA function of the 9160. I have verified that it works with the official http_application_update project, but when I test it with my own project...
I want to connect remocon and nrfboard. A nd see the value of the remote control as uart.
so I try to connect remocon and nrf85832 to use SDK 13.1 example.
I use central...
This is a new install of NCS 6.1. Installed using nRF Connect Desktop v3.7.0 Toolchain Manager and connected to a new nRF5340 DK.
I followed the Getting Started, Running...
HI Nordic,
I am working PCA10040, SDK17.0.2, ble_app_uart routine.
I'm try to add ADV/SCAN_RSP data, but when I add some field, such as p_manuf_specific_data or service_data_count...
nrf52840 nrf5_sdk 16.
Looking to use the LPCOMP to wake the nrf from System OFF.
Question: if I config the LPCOMP to use the internal reference "15-level internal reference...
Excuse me:
Suppose I Initialize and turn on UART and the power consumption is 4mA，When I call app_uart_close() the power consumption is 2mA,If I don't initialize UART at...
Hi all,
I have been trying to work with UARTE for both TX and RX, and my test code is working with RX perfectly but not TX, when i try to transmit my data using uart_tx...
Hi，
I am doing a micphone " sph0641lm4h-1 ", and I use api of nrf_drv_pdm .c,
when I read mic data from sph0641lm4h-1 , they are just sets of 16 bit data, the following...
Hi. Thank you for your interest in my writing. I'm working on the IOS and the Multiple Connection project at the experimental_ble_app_multiperial example. It's a project that...
Hello,
I have been using the TWIM peripheral of the nRF52832 (via the twi_mngr) to talk to an accelerometer and a magnetometer. I have 4.7k ohm pullup resistors (in parallel...
Hi,
I am using nrf52840 customized dongle in our project. We have interfaced ADS1118 using spi communication with nrf52840 (customized dongle). The problem here with the...
I am trying to build the 'BLE NFC pairing reference' example for nRF52840.
I downloaded the latest SDK and located this example in the experimental directory under BLE\Peripherals...
nRF52840
SDK 15.3
Segger Embedded Studio
I PWM a piezo buzzer (with a transistor) , using the PWM peripheral. The problem I encounter is that before I call the PWM...
