nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Hi,
I have bought a Thingy 91 and have connected to the nRF cloud etc. and I am getting the sensor data OK.
The GPS is still not working, I have followed the instructions...
Hello,
I would like to calculate maximum range between two devices equipped with nRF52840 transceivers working in the IEEE 802.15.4 radio mode. Can I assume that -100 dBm...
Hello,
I have a question about Bluetooth connectivity issues. The BLE code I'm trying to make will be connected to the smartphone (Android). If phone out of the Bluetooth...
I'm developing a bluetooth device that only advertises data, it's set to BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE and BLE_GAP_ADV_TYPE_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
Hello everyone,
Can I use the latest nrfutil 6.1.0 tool to generate the DFU zip file for the dual_bank_bootloader in SDK11?
If yes, do I need to keep the --hw-version...
Hi, I wanna enter the system on sleep to save the power up to 10uA(about tens of A). I am using nrf52840-dk with SPI LCD and some GPIOs in zephyr. Also I want to do DEVICE_POWER_MANAGEMENT...
Hi, I would like to run an nrf53 example project. I got the devkit, and after some struggle I am now able to compile and run a project.
I need to run an Bluetooth example...
This is really a question about best practice - I have some ideas of ways to do what I want, but wonder if there is some clean API-supported method that I haven't found.....
Hi, I am in design stage and i need to change nrf 8001 to nrf 52810. In this point i have a question about pin configuration in nrf52810, Can i use any pin for any use? i...
Hello everyone.
I know from Errata document that the GPS antenna soldered on DK is not working properly on the 0.8.2 version of the DK. I need to use GPS for time syncronization...
Hello,
We are allocating a large amount of pages (100 pages, ~400kB) for the Flash Data Storage module in order to hold collected data. As a result, the fds garbage collection...
Hi all, can the nRF52840 dongle be used as an external Bluetooth 5.0 peripheral via a Raspberry Pi 3 running Linux?
I received this message from my engineer
' The drivers...
This is based on the article fround in devzone here .
I'm compiling a simple Hello World and followed the instructions as per the nrf Connect SDK Turorial Part 2 .
To...
Howdy,
I'm using Zephyr to configure an nRF52840 to act as an I2C master and send data to a TM4C slave at a 100kHz clock rate. The nRF52840 appears to hang after calling...
Hello, I am working with nRF5 SDK 17.0.0 and using IAR Embedded Workbench 8.50.1. I am following the Secure DFU bootloader guide as posted here .
On Step B3, I get a build...
