Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I am trying to get a project to compile using the the segger studio. I have copied one of the example applications and converted it according to your instruction here...
Hello,
I want to add a new driver directly in my project (out of tree), so I've add the differents files, as in the picture below.
When I compile, I get each time...
HI
I used NRF24L01 module in direct mode and chose 250kbps in configuration
In TX mode : whether the data from MCU to module has to be send through exact 250kbps?
Dear Sir
I am trying to work with the ADC .
Attached a code
I get the lines
00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772...
Hi Nordic Team,
Some time facing Connection issue in Mobile app and some time device advertisement is not getting in app.
I am using below chipset and configuration. ...
Dear all, I try to self provision device by it self following steps below: Step 1 : Bind key Step 2 : Subscribe to topic
Step3 : Set publication topic
Step 4 The main...
I am having issues running GPS and LTE concurrently on the nRF9160DK and am wondering if the rootcause is an incompatibility between modem FW v1.2 and hardware v0.9.0. I am...
Hello,
With regards to the HID Keyboard Example,
1) Is it posible to disconnect from the central side (ios)? I would like to be able to disconnect as follows:
But...
Hi,
I have just started using the Nordic SDK (nRF5_SDK_15.2.0_9412b96) and am developing a low power application for a custom PCB using the rf52840.
I am developing...
I can read the spi flash id by the other mcu with the above code, but can not read correctly by
nrf52832, is there something wrong with my handle?
SPI FLASH ID 0E 40 13...
Hi!
We experience some problems with DFU, and while looking through the code, I saw the code copied below.
This is from the file dfu_req_handling.c from SDK14, and my...
Hello everyone,
I am programming my dongle(nrf52840) with my Dk. To upload the code I click on download "solution_name" in the target menu, it works fine for example without...
I am using NRF52840 Dongle to scan all the BLE advertisement packets.
I wish to scan for the BLE advertisements packets only from a particular device using the whitelisting...
hello all,
i am trying to add ble app uart feature in other ble app project. so i am trying to change those defines variable, NRF_SDH_BLE_GATT_MAX_MTU_SIZE & NRF_SDH_BLE_VS_UUID_COUNT...
