Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I have never used the GPIOs near the RF pin (GPIO 22, 23, 24), until my latest project, which I needed to due to pin limitations. It is normal for pins adjacent to RF outputs...
Hi.
I try to test using ble pc-drivce C library & 52840 dongle on pc.
except custom service. everything is fine.
under below is custom service pic.
...
This seems to be a recurring question. I suspect the Wireshark/nrf-Sniffer setup is delicate enough that minor changes/upgrades in any of the components causes a problem....
nrf52832 , SDK_V15.3 , ble_app_uart sample code , data communication problem.
Hello there...
I use the SDK V15.2, ble_app_uart sample code, on the nrf52832
seems the...
Hello,
Currently working with Segger 4.42 and SDK 15.0
I've searched around the devzone on doing a passkey connection between my server and central.
I've used the ble_app_gls...
Hi, I'm having trouble pairing with Android devices using the SDK's ble_app_gls example, when I try to pairing with any andoid device it throws the following error "couldn...
I Modify my code for 7 buttons from 7 gpios. But my code has a issue at sdk_config.h. The define of GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS is 9. When I built the code and download...
Hi all,
The nRF52832 spec. document specifies that the current consumed in System OFF / No RAM retention / Wake on LPCOMP mode is 1.9uA. However, if I measure the current...
Hi,
A couple of months ago, the Bluetooth SIG published a specification for LE Audio : a new codec and method to send audio data through BLE 5 connection.
Is there an...
Hello,
Few questions about NUS and NUS C please.
Is there any way to know how many TX are pending ?
Are TX notify or indicate ? How to change it please ?
Thank yo...
Hello,
Based on aws_fota sample, I want to replace the line with poll with something that not blocks (because I have another things to manage in my loop). Do someone have...
Hi,
I am evaluating nRF52840 DK as a peripheral with 300ms interval with no timeout (continuous advertising with APP_ADV_DURATION set to 0 ).
I understood that while APP_ADV_DURATION...
I am developing for an nRF52810 target application.
I am using IAR 8.42 with a PE Micro debugger. If I debug a project (call it project A), the linker ROM space starts at...
Hi,
I tried the SDK_DIR\examples\dfu\secure_bootloader\pca10040_s132_ble example from nRF5_SDK_16.0.0 with my custom board with nrf52832 mcu.
I followed this guide:
...
