nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Hi,
I have connected my custom pcb to the development kit at pin 19. When i use jlink commander, the board is detected properly. I use nrfjprog to dump the softdevice(Using...
I'm trying the get the development kit of the nRF52832 (PCA10040) displaying a floating point value. I read several postings of this problem, but non of the suggested solutions...
Hi, I'm having an I2C read lock-up issue similar to those described here , here , and here .
I'm using SES, SDK14.1, and an nRF52382. The only other component on the I2C...
Hi,
I have a custom board with nRF52832 SOC and temperature sensor in it.Interface Between the nRF52832 and Temperature sensor is I2C.i have to see the data through the...
Hello
We are currently making STN1170 based OBD II scanners with the nRF52810 for communications. The product is stable and available for commercial deployment, however...
Hello Supporter,
I'm going to develop one BLE nrf51822 based custom device. in which i want to use BLE DFU.
i am able to load DFU and APPLICATION with KEIL uvison 5. ...
Good morning, I have a question about MESH RF. We need connect many vehicles to station base via RF. - Station base --> UART --> RF Device [ MESH ] (SKY CLEAR and outdoor...
Hello Nordic community! My setup is pca10040, android tablet, s132, sdk14.2.
This time I am trying to understand why this code:
While using nrf toolbox nrf UART prints...
Dear All,
I would like to explore the possibility of repetitively transferring small amount of sensor data from an nRF52832 to an ANT(+) compatible Android device, for a...
We are using an MDBT42V(29 pin) module which we discovered from the datasheet, comes with an nRF52832 controller. We are using a nRF52 DK to dump codes into this target board...
I am using nRF Connect (PC version) a lot to debug my application. I am using a PCA10040 board as dongle and everything works fine most of the time. But after I keep the nRF...
SDK 14.2 libraries/util/sdk_errors.h includes sdk_config.h but does not use it. In other words, it falsely expresses a dependency.
This makes it harder to compile code ...
I'm trying to send a string of 140 characters length using UART.....but only 98 characters length is being recieved in the output.
what could be the issue? How many bytes...
I am using nrf52 with SDK 14.2.0 and SD is S132.
The issue I am facing is that after Central is paired with one peripheral and bonding is done, the bonding information...
Hello! I am attempting to prototype a solution that implements a peripheral with the battery service that connects to multiple central devices. I see in the ble_app_multilink_central...
