Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hello. I have a question about how to enable a 32 MHz crystal oscillator on a custom board? I have 32 kHz and 32 MHz quartz crystals on the board. I found the following config...
Hi. This is a problem that occurs on a customer's factory test client unit. Issue occurs roughly about once every few months.
Customer Development Environment Info:
OS...
Hi,
I am stuck during migration from ncs 2.6.2 to 2.7.0 (I want to finally reach 2.9.0):
``` [00:00:13.276,275] <err> bt_sdc_hci_driver: SoftDevice Controller ASSERT:...
Dear customer support people,
I'm trying to employ a particular signature scheme to benchmark it against other more traditional methods on your devices, specifically on...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
Kicked off an application FOTA update, and somehow it failed:
[00:02:06.161,315] <err> download_client: Error in recv(),...
I've built a firmware based on the hci_uart sample with the softdevice controller. The board is custom made and has a nrf52840 on it. Over USB-CDC HCI commands are sent to...
Is there any issue with using the nRF52833 DK/nRF52833 for Matter development? I’m asking because the Matter template doesn’t seem to support the nRF52833 DK/nRF52833. If...
Dear Nordic People Recently I am following YouTube link from Nordic Semiconductor for Implementing ESL https://www.youtube.com/watch?v=VeLkptpSvRQ This video requires specific...
Hello and thanks for reading. Also happy holidays.
We are using an NRF5340, and are having some issues with connectivity. I would therefore welcome any suggestions you may...
Hello
I've been experimenting in increasing the number of targets that a mesh FOTA distribution server can support on nRF52840
The CONFIG_BT_MESH_DFD_SRV_TARGETS_MAX has...
We want to upgrade our existing product to WiFi 6. We have a lot of customization in our TCP/IP stack so we don't want to use the zephyr stack. We only want to make the station...
While in the field test phase of our custom nrf9161 based device, we figured out that there are some towers of some providers that make the device seem online although it...
Hello,
I need to use the Radio_test example on a custom board using the nrf52810. I am using the nrf connect SDK 2.5.1 with VSCode.
To use the Radio_Test example I need...
Mesh 1.1 Generic Location Server defines special values for long/lat and north/east when unconfigured. Current code doesn't appear to support/use these special values, instead...
Hello everyone,
I am developing a ble project that builds on the peripheral Uart example using the sdk 2.4.0 for nrf5340.
I want to implement a watchdog since I sometimes...
