Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
I'm running SDK 2.8 and 2.8 Toolchain. I created the sysbuild.conf setting:
SB_CONFIG_BOOTLOADER_MCUBOOT=y
and put it in the application folder (per this support request...
Hello, I am relatively new to the nRF 5340 Audio DK. I recently ordered a singular nRF 5340 Audio DK board and my goal was for the board to take in input audio via the PDM...
Hi all,
I've been using the nRFConnect extension without any issues, successfully connecting to my nRF5340 board via JLink, flashing firmware, and receiving printed messages...
i get the following build error whenever i build for boards other than nrf
- CMake version: 3.21.0 -- Found Python3: C:/ncs/toolchains/b620d30767/opt/bin/python.exe (found...
Hello,
I encountered a compilation issue when using the app_timer function. The error message is: "'TickType_t' undeclared (first use in this function)". I believe the problem...
Hi,
I am trying to set the VDD pin to 3.0V instead of the current 1.8V (also changing the GPIO voltages to 3V). I've seen many questions related to that but no solution...
Hi Support Team
May we know that the difference between Engineering Build Code BB0 of nRF54L15 with normal Build Code? Which is recommended for the mass production of customer...
Hi, I am using nrf9151-DK to send and receive data over UDP protocol. Firstly, I tried to use AT commands to send and receive meassages as described here , I had no isuues...
Hi,
How can I control a Thread CoAP Client, which is connected to a thread supporting modem such as eero+ (in other words, the CoAP client is connected to the internet)...
Hello
I am trying to build the Zephyr mesh distributor sample on the nRF 52840 dongle
It builds and runs just find on the nRF52840 DK
But when I try to build for the...
Hello,
I'm looking at adding USB DFU to my project, (Not USB DFU recovery in the bootloader, but in runtime) and was trying this example. It fails to build for the nordic...
Hi,
im develop a keyboard by ncs sdk in nrf52840,and one funcation is that power off/on the keyboard ny fn key .i see the CAF: Power manager module , It doesn't seem to...
Hello, I've been developing on a Nrf5340 board and I am trying to gather pressure sensor data from both a adafruit mprls pressure sensor breakout board on i2c and then a Honeywell...
I've been tasked with studying adding Auracast to an application. One fundamental thing I can't get my head around is what is the s/w requirement - i.e. do I need 3rd party...
