Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi,
I'm developing with nRF Connect SDK v2.9.0 in VS Code. I followed the exercise l1_e1 from the intermediate course. When I debug with breakpoints and the first breakpoint...
Hello there,
I reported this issue in another thread under a different symptom. With more and more testing, it shows it is somehow related to both Android and the 54L15...
Hello.
I need to read IMU data from LIS2DH12 of nrf 52833 which is in DWM3001CDK. But nothing I do initializes sensor... i always receive
<err> lis2dh: Failed to read...
Hello!
I am learning to obtain data by SPI protocol from ICM20948 sensor using nRF54l15. I tried to write my code based on sample given on devacademy nRF Connect SDK Intermediate...
We are developing with the nRF9131EK. But there is no documentation of this board.
https://docs.nordicsemi.com/category/nrf-91-series
Can You add the information like...
Before developing our custom board, we connected our MCU to the DK via pins 26, 27 and after disabling VCOM0 via the DK configurator, we were able to communicate using AT...
Hello,
I wanted to know if the "direct test mode sample" could be used for the EVK-ANNA-B402C that integrates the nRF52833 in its SIP.
Because building with the board...
I have a nrf52840dongle and a nrf54l15 custom board. And I flashed bt hci_usb demo into nrf52840dongle, uart_peripheral demo into nrf54l15 board.
Now I want to use my nrf52840dongle...
I am performing a BLE DFU update on an nRF52840 using the nRF Connect Android app (v4.29.1) . The app successfully uploads the DFU package and reports that the update is completed...
Hello, Nordic team.
We started to fight with the nrf52-ble-image-transfer-demo repo (congratulations on the project, ovrebekk ).
We are using the nRF52840 DK (PCA10056...
How to control the Power (change from 8 dBm to -40dBm) we can relate and keep this delta as reference and check the rest of the current?
How to set the Standby and Sleep...
i am using SDK 1.9.1 to notify data to peripheral to central device i am using ''bt_gatt_notify " api to send data to mobile but i am able to send only 20 bytes data to central...
Hi
Is there anything in particular I need to do to enable ZMS for the nRF54L15?
I am trying to include the ZMS sample code into my own sample built for the 54l15 appcore...
Hi,
Can anyone tell me the difference between BLE IPC and BLE RPC implementation? I'm little confused.
Refer to these kconfig symbol,
SB_CONFIG_NETCORE_IPC_RADIO_BT_HCI_IPC...
Greetings!
Our device will use WiFi network to send data to the Azure's IoT Hub, where it will be further forwarded to our cloud. As the used network won't be controlled...
