I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
SAADC resolution is set to 8 bits, channel is configured as single ended. Is it correct to say that SAADC digital output should be between 0x0000 and 0x00FF(full scale)? ...
Hi,
I'm testing the ble_app_uart example on the nRF52840 DK and it seems to be consuming a lot of current similar to the case in https://devzone.nordicsemi.com/f/nordic...
In a single core BLE SOC, whenever a BLE event occurs the BLE stack takes high priority and any application code running on the single core, is delayed while the event is...
Hi ,
I need to store strings in flash and came across the NVS. I referred to the example in samples/subsys/nvs and was able to do the nvs operation.
The following are...
Hey, so I was under the belief that the maximum size of data one can include in a BLE packet is 20 bytes (23 bytes total, 3 bytes overhead, so 20 total for custom data). With...
Hello! I have been working on bluetooth for some time and I just worked with connectable advertising until now. This time I am trying to add a beacon functionality too. The...
Hello,
I am developing a BLE and IEEE 802.1.4 multiprotocol device. I implemented a parser to change some settings of the device. T he configuration is updated with this...
Hi,
I'm trying to implement a SPI Communication between Arduino UNO and PCA10056 DK. PCA10056 DK run as a SPI slave.. Arduino uno run as a SPI Master.
The problem is...
I'm using SDK 15.3.0 and SoftDevice 6.1.1 running on an nRF52832.
The iOS application works correctly when it is running in the foreground. It is able to connect and bond...
Hi,
I am trying to develop an application for Thingy:91, which would allow me getting data from BLE and sending it to the cloud with LTE. I am working on NCS 1.3.0.
Of...
I just tested with the example project, "ble_app_uart" using SDK, "nRF5SDK17009d13099.zip" on nRF52DK (labelled with PCA10040 1.2.4 2018.23) board on Segger embedded studio...
Hi ,
i am trying to interface a WINBOND W25Q64JV flash module with NRF52,i can able to read device id,status register success fully.
i wrote the data in particular address...
Hi,
I'm using nRF52840 DK as a central. Our project is based on ble_app_uart_c example. There is filter for UUID only during scan.
I noticed, that for conection establishing...
