Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi
I'm trying to build blinky example (from SDK17.0.2) to run it on nRF52833DK.
The board is running correctly if I download the hex comes with SDK but failed if download...
Hi, I'm writing a library for the common Hitachi_HD44780 (LCD2004 etc) but need it to be non-blocking. I'll open source it once done. I'm using EasyDMA to do the transfers...
Hello,
I am trying to solve my issue for few days without success hence your help would be appreciated. I found a lot of related issues, but any of the solutions doesn't...
Hello,
I am using nRF52840 chipset and I was using the Segger tool chain properly. But recently I started getting below error "The evaluation period of this release has...
Hi,
I am doing the project in nRF2832 , where I need to collect some data from the sensor and temperature value that i need to save in the .CSV file format in SD cARD ....
Hi,
I have a question about setting the gpio pin status. From the picture, it seems that the value on the right represents the status of the gpio pin. So the default value...
I'm using NCS 1.4.0 and 2 boards nRF5340PDK.
I'm using central_uart and peripheral_uart samples. Both display when connection interval change.
The central_uart use BT_LE_CONN_PARAM...
can You explain
light_lc_client_light_onoff_set(&m_clients[0], &set_params,&transition_params);
This command in the lc client used to make the immediate on the server...
I'm implementing a project that attempts to change the TX power of itself during runtime. I have used the set and get functions from the Zephyr sample: https://docs.zephyrproject...
Hi guys, Do we have an outlook on silicon in which errata bugs 174, 195 & 198 (SPIM3 bugs) are solved?
Best regards,
Casper van Doorne
Pink Fluffy Unicorns BV
I am trying to make the LSM9DS1 connected with the nrf52840,
1. Now I am trying to send the hex array to the lsm9ds1, seems always failed.
any suggestion how to make...
Hi,
In my aplication, I bring my nRF52840 into power system off mode with s d_power_system_off on several different events, most notably the BLE_GAP_EVT_DISCONNECTED event...
Hi Team,
We have developed an application where we are able to receive scan request notification in peripheral and scan response notification in central.
Is it possible...
Using the nRF Connect SDK from Nordic Semiconductor is a terrible experience. One reason it being unreliable with many broken samples. And another being the Segger Embedded...
HI,
I'm using Nrf52840 device and connecting my mobile.
After inserting the authentication code for the pairing process.. phone connects successfully and after a few seconds...
