I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Members
I am in the board design phase of my project. I use Arduino boards (Due & Uno) with SPI. I read that the nRF24L series is not recommended for future projects....
Hi,
So I am using nRF51822 chip to develop our products. We have two motors attacked to our PCB and we want to control the pulse with low power PWM. We want to control...
Hi...
i want to read the data from another board using serial uart .. how to write the command to check the data is available ... in arduino i written like this how to write...
Hello,
I used to use two nRF52810 for testing.
Using Timeslot (BLE+ESB), one of the 52810 paired mobile phones Bluetooth simultaneously sends the ESB.
Another 52810...
What are all the configuration options necessary to configure the nRF9160 as a SPI slave? I'm working with a custom board and have specific DTS files I'm working with. Here...
Hi Nordic Team,
I'm quite confused and can't find a concrete answer so far on the forum, if it is a MUST to kick-off a certification at the Bluetooth SIG Group or not, if...
nRF52840 SDK 15.2
I want to control the power of sensor, so I configurate the pin like this:
nrf_gpio_cfg(AFE4403_PIN_PWR_EN, NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_DISCONNECT...
HI,
I am using ".\nRF5_SDK_15.3.0_59ac345\examples\peripheral\wdt" to test “watch dog timer function.
My use case is:
1. If the program is not execute over following...
I have developed ble periphleral device to send 20byte long at every five seconds to the central. Because connecting to serial to PC, I didn't realize the device cannot not...
Hi,
I need to run RTC simultaneously with Softdevice without external low frequency clock source (32.768kHz oscillator).
I used following settings to setup RTC,
RTC_ENABLED...
I am trying to make a central device that is similar to the NUS central example in the SDK. I have a function that is the same as ble_nus_chars_received_uart_print to print...
In the ESB stack, only a sub-set of available transmitter powers are enumerated in nrf_esb_tx_power_t.
Is this deliberate? The hardware supports a much wider range of values...
I Performed a clean reinstall of all tools and packages.
core_cm4.h file exists at location: C:\..\..\..\..\..\Nordic\nRF5_SDK_15.3.0_59ac345\nRF5_SDK_15.3.0_59ac345\components...
Hello,
I would like to clear some of my confusion on multi peripheral links behavior.
My context: SDK 15.2/SD610 on 3 52840 nodes.
I am using multiple peripheral links...
