Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi
I am developing RX device to connect with Smart Remote 3.
The RX device system is Linux embedded. I need to run OTA function in Linux embedded to update SR3 F/W.
...
Hi,
I am using STM32F030C6 MCU with Laird BL651 module.
Keil-IDE v5, windows 7(64-bit) system configuration.
I need to get the sample code for the application development...
Hello, I have following problem.
My DK is not recognized by J-Link / nRFgo Studio.
I tried to reflash J-Link by pressing BOOT/RESET and then drag and drop J-Link OB...
Hi,
I would like to update the Device Information Service's (DIS) serial number characteristic to reflect the actual serial number assigned by our production equipment....
Hi, I am using the following setup: Wireshark 2.6.5 (updated yesterday) Sniffer 2.0.0-beta-3 (nrfsniffer200beta312oct20181c2a221.zip) nRF52840-DK (used by the sniffer) nRF52840...
I have a custom board that uses Nordic NRF52832 as MCU. For laying out crystals, BLE part and decoupling capacitors, I used reference layout from documentation.
32 MHz crystal...
Hi everyone,
My hw/sw configuration:
- nRF52840 - sdk 15.0.0 - softdevice: s140_nrf52_6.0.0
I would like to change the device name and update it in advertising packet...
Hi All,
I have been working on ipv6 over ble on zephyr RTOS to form mesh network.I have been successfully integrated "rpl_node"(which is in zephyr/samples/net/rpl_node)...
Hi guys,
I have very strange problem with the Android phone when connect with nrf51822.
After connection, I used update parameters to set the parameters on the phone side...
Hello,
I am attempting to program nRF52 DK modules to communicate using the UART over BLE central and peripheral roles as in the examples provided in SDK 15.2. The data...
hello, I have used NRF52810 TWIM for 24LC08 communication, and I got a problem.
when I want to read data from 24LC08, if the length is not lager than 255, every thing is...
Dear all,
Good morning,
We are using nrf52832 as our main mcu. Our current consumption in system-off mode in custom board is around 3.2 mA which is very high and we want...
HI devzone
We now use NRF52832 to implement TDMA protocol.
In our application, there is one primary node and six sub-nodes.The communication process is as follows:
After...
I want to add simple on off switch model via SDK 2.2.0.
I'm already add client model to project,when provisioner add client node,Provisioner RTT jump error opcode status...
Hello Everyone,
Maybe this is a very silly question.
I am trying to implement timer in nrf51822 with S130, SDK11.
Code snippet:
void TIMER1_IRQHandler(void)
...
